General Usage - Southwing SH440 Guia Del Usuario

User guide_SH440.qxd 22/12/2006
Then complete normal pairing
process by following point 1
and 2 of the auto-pairing sec-
tion above.
3. WEARING AND CARRYING
THE HEADSET
You can wear your Headset on
either ear and carry it in different
ways using the rotating Multi-
function Arm [7].
Wearing the Headset without
the Ear Hook
You can wear the Headset with-
out using the Ear Hook. To do so:
1. Rotate the Multi-function Arm
[8] downwards, until it stays in
your ear like a wired headset
cable extension.
2. Gently place the Speaker [5]
into your ear canal.
3. Finally find the most comfort-
able position by rotating the
Headset forward and backward.
Wearing the Headset with
the Ear Hook
The Ear Hook may also be used
for maximum comfort. To mount
the ear hook, rotate the Multi-
function Arm [7] upwards and
slide it inside the Ear Hook [8]
jack. To place it on your ear fol-
low these steps:
1. Rotate the Ear Hook [8] slight-
ly forwards.
2. Gently place the Speaker [5]
into your ear canal.
3. Rotate the Ear Hook [8] back-
4
16:09 Seite 4
wards and adjust it behind your ear.
4. To switch from one ear to the
other, simply rotate the Multi-
function Arm [7] downwards and
rotate the Ear Hook [8] to the
opposite side.
Clipping your Headset to your
clothes
The Multi-function Arm can also
be used to carry your Headset in
several convenient ways (Ear
Hook not mounted). To clip it to
your clothes do the following:
1. Rotate the Multi-function Arm
[7] to the same direction of the
microphone [6]
2. Use the Multi-function Arm [7]
and Headset Body as a clip to
attach the Headset to your
clothes.
Using your Headset Cord to carry
your Headset
The Headset Cord [9] can also be
used to carry your Headset with
your mobile phone (Ear Hook not
mounted). To attach your
Headset to the Headset Cord [9]
follow these steps:
1. Rotate the Multi-function Arm
[7] until it is in opposite direction
of the Headset microphone [6]
2. Attach the Multi-function Arm
[7] to the Headset Cord [9] jack

4. GENERAL USAGE

Turning the Headset on and off
To turn the Headset on, press
and hold the On/Off Button [2] for
about 3 seconds until a series of tion Button [2]. You will then be
tones is heard. The Indicator able to speak the name of the
Light [2] will flicker for 1 second person you wish to call.
and start flashing.
Ending a call
To turn the Headset off, press
and hold the On/Off Button [2] for Press the Multi-function Button
about 3 seconds until a series of [2] briefly during a call and the
tones is heard. The Indicator call will be ended.
Light will flash, before turning off.
Disconnecting from the phone*
Changing Volume
You may wish to disconnect the
To increase the volume, during a Headset from the phone in order
call, press Vol+ Button [3]. To to reduce battery consumption.
decrease the volume, press the To do so, press the Multi-func-
Vol- Button [4]. The Headset will tion Button 3 times on the
remember all volume settings Headset when it is not in an
even when it is switched off. active call. If you want to pick up
a call, you first need to re-con-
Accepting / rejecting* a call
nect the Headset. To do so,
When the phone rings (ring tone press the Multi-function Button
can be heard in Headset), briefly once again on the Headset.
press the Multi-function Button
Battery life
[2] once to accept the call. Press
and hold the Multi-function To conserve battery life, your
Button [2] for 1 second to reject Headset features an auto-sleep
the call. function. This function switches
the Headset off after 12 hours of
Initiating a call from your
inaction. Once your Headset has
mobile phone
entered auto-sleep, it can be
Dial the number as usual with switched on again normally.
your phone. If your Headset is on When the battery has only 10%
and the phone has been correct- charge remaining, the Headset
ly paired, your phone will transfer will produce an audible warning
the call to your Headset. tone sequence every time a call
is ended.
Initiating a call with voice dialling
Resetting your Headset
You may be able to initiate the
voice dialling function from your Should your Headset stop res-
Headset (your phone will need to ponding, try charging it for a few
support voice dialling and voice seconds. Your Headset should
tags need to be entered). To acti- now function again as normal.
vate, briefly press the Multi-func-
* The features marked with an asterisk will only work with Bluetooth phones which support the Hands-free profile.
Today, most Bluetooth phones support this profile.
5