Trueshopping JSG3IN1BC Manual Del Usuario página 2

CAUTIONS:
▪ Allow one (1) hour cool-down period before recharging.
▪
It is highly recommended that this product be operated by two persons. ENSURE that someone is available to give assistance, if needed.
▪ Wear complete eye and clothing protection. Do not touch eyes while working near battery.
▪
ALWAYS keep the booster clamps in their storage holders to prevent sparking when recharging and when they are not in use.
▪
When using the 120 Volt AC or 12 Volt DC charger, pull on the plug and never pull on the cord when disconnecting.
▪ DO NOT recharge product battery with damaged chargers, replace them immediately.
▪
DO NOT attempt to remove or replace the battery used in this device. When battery has reached the end of its useful lifetime, take the entire unit to a battery recycling
facility for proper disposal and /or battery replacement.
▪ Avoid dropping metal tools onto vehicle battery. It might spark or short circuit battery or other electrical part that may cause short circuits or explosion.
▪ For proper and safe operation of the Portable Power Source 12 Volt DC power socket DO NOT place anything into the socket except the plug of the 12 Volt DC accessory to
be used.
▪
DO NOT place anything into the Portable Power Source charging port except the provided plug from the charger unit.
▪
Remove personal metal items such as rings, bracelets, necklaces and watches while working with a lead-acid battery. It can produce a short-circuit high enough to cause a
severe burn.
▪
Never charge or jump-start a vehicle with a frozen battery.
▪
Never allow booster clamps to touch together or to contact the same piece of metal to prevent short circuits and arcing.
▪
Do not operate this device while wearing vinyl clothing. Static electricity sparks maybe generated when vinyl clothing is rubbed.
▪
This product is not intended for use in the rain or temperature above 130˚F.
▪
Use only the provided chargers, cables and clamps. Unauthorized parts may damage the Portable Power Source.
▪
This product has no consumer serviceable parts, except the inverter replaceable fuse. This is not a toy. KEEP OUT OF REACH OF CHILDREN!
▪ Keep battery terminals clean. Be careful to keep corrosion from coming in contact with eyes.
▪
Save these instructions for future reference.
JUMP STARTING (BATTERY BOOST) INSTRUCTIONS:
WARNING:
Vehicles equipped with on-board computer(s) may be damaged if vehicle is jumpstarted. Read your vehicle owner's manual before attempting to start the vehicle to
determine if external-starting / battery boosting assistance can be used. Failure to follow these instructions may cause damage or explosion. Use safety glasses to protect
eyes while jump-starting (battery boost) a vehicle. ONLY Jump Start / boost charge a vehicle in a clear unobstructed, open area.
CAUTION:
ENSURE that the Portable Power Source booster switch is in the OFF position. Place this unit on a flat and stable surface near the vehicle battery that is clear of all moving
parts (fan blades, belts, and pulleys). DO NOT smoke, use matches, lighters or open flame while attempting to jump-start (battery boost) a vehicle. Use extreme caution DO
NOT touch battery clamps together.
1. Turn OFF the vehicle ignition and all accessories (e.g., Radios, Lights, Air Conditioner and Cellular Phones).
2. Set the emergency brake and put vehicle with automatic transmission in the PARK position.
3. Determine the polarity of the vehicle battery terminals. The Positive (POS,P,+) battery terminal usually is larger in diameter than the Negative (NEG, N, -) terminal. (If you
are unsure you should refer to vehicle owner's manual).
4. Determine whether your vehicle uses a Negative or Positive Grounded System:
Negative Grounded system: Negative battery terminal is grounded to chassis. Most vehicles use this system.
Positive Grounded system: Positive battery terminal is grounded to chassis or any other metallic part of the vehicle (If you are unsure you should refer to the vehicle
owner's manual).
5. Access the Portable Power Source booster clamps by squeezing the clamp handles. Pull the clamps outward and remove clamps from their storage holders. NEVER allow
clamps to touch together or to contact the same piece of metal to prevent short circuits and arcing.
6. Follow instructions for Negative Grounded system or Positive Grounded system as indicated below:
Negative Grounded system:
a. Securely connect the Positive (+) Red clamp to the Positive ( POS, P, +) terminal of the vehicle battery or the remote Positive (+) terminal if equipped.
b. Securely connect the Negative (-) Black clamp to the vehicle chassis, engine block or a non-moving grounded metal part of the vehicle as far away from the battery as
possible. Do not clamp directly to carburetor, fuel lines, or non-grounded Sheet-metal body parts.
c. Portable Power Source Green LED is ON/Lit. (Proper battery polarity Connection.) WARNING: IF RED LED is ON/Lit and alarm sounds (reverse battery polarity connection)
STOP! CAREFULLY DISCONNECT the Portable Power Source booster clamps! Reconnect the Portable Power Source booster clamps to the proper battery polarity ( Red
booster clamp to the positive terminal of the battery and the Black booster clamp to vehicle ground.)
d. See Jump Starting (Battery Boost) procedure #7 (below) to continue.
Positive Grounded system:
a. Securely connect the Negative (-) Black clamp to the Negative (NEG, N, -) ungrounded terminal of the vehicle battery.
b. Securely connect the Positive (+) Red clamp to the vehicle chassis, engine block or a non-moving grounded metal part of the vehicle as far away from the battery as
possible. Do not clamp directly to carburetor, fuel lines, or Sheet-metal body parts.
c. Portable Power Source Green LED is ON/Lit. (Proper battery polarity Connection.) WARNING: IF RED LED is ON/Lit and alarm sounds (reverse battery polarity connection)
STOP! CAREFULLY DISCONNECT the Portable Power Source booster clamps! Reconnect the Portable Power Source booster clamps to the proper battery polarity ( Black
booster clamp to the negative terminal of the battery and the Red booster clamp to vehicle ground.)
d. See Jump Starting (Battery Boost) procedure #7 (below) to continue.
7. Turn the Portable Power Source booster switch clockwise to turn ON power to the booster clamps.
8. Allow 2 or 3 minutes charging time. It is recommended to have a second person to assist holding the Portable Power Source unit securely in place during the next steps.
9. Turn the ignition key and attempt to start the vehicle. Note: If the vehicle does not start after 4 to 5 seconds of engine cranking...stop...wait 3 to 4 minutes, then try
again. Repeat several times until the vehicle starts.
CAUTION:
Excessive engine cranking can damage vehicle starter motor. If the engine turns, but fails to start after several attempts, other technical problem(s) might be involved.
Discontinue cranking the engine until the other problem is determined and corrected.
10. If the vehicle starts, turn the of Portable Power Source booster switch counter clockwise to the OFF position.
11. Disconnect clamps in reverse sequence to connecting procedure above as far away from the vehicle battery as practical: For Negative Grounded System first disconnect
Negative (Black) then Positive (Red) clamps. For Positive Grounded System first disconnect Positive (Red) then Negative (Black) clamps.
12. Replace the clamps to their storage holders.
LED LIGHT & EMERGENCY FLASHER INSTRUCTIONS:
1. To power ON the LED Light, press the push-button switch once and release.
2. To power OFF the LED Light, press the push-button switch once more and release.
3. To power ON the Emergency Flasher, press the push-button switch once and release.
4. To power OFF the Emergency Flasher, press the push-button switch once more and release.
NOTE: LED light or emergency flasher functions will operate in sequence to each other. The lighting mode will depend on the prior (last) operating function selected.
User may have to cycle between modes in order to achieve the proper lighting function.