Trueshopping JSG3IN1BC Manual Del Usuario página 4

COMPRESSOR INSTRUCTIONS:
WARNINGS:
▪ DO NOT operate the air compressor around flammable materials or in an area where flammable fumes are present!
▪ Check item to be inflated for manufacturer's maximum recommended inflation pressure. DO NOT over inflate! Most tires are properly inflated
between 24-35 PSI. Some truck & bicycle tires require 40 PSI or more.
▪ Always check the tire air inflation pressure with a separate air pressure gauge during and after inflating.
▪ DO NOT operate compressor more than 20 minutes continuously. Allow the compressor to cool down between each continuous operation.
▪ BURSTING HAZARD! DO NOT overinflate any inflatable article! DO NOT exceed the manufacturer's recommended inflation pressure!
A. TO INFLATE PLASTIC INFLATABLES (BALLS, AIR MATTRESSES, RUBBER RAFTS, ETC.)
CAUTION: Check manufacturer's specification on item to be inflated for correct inflation pressure. DO NOT over inflate!
1. Remove the valve cap from the inflatable valve stem.
2. Connect the compressor air hose nozzle onto or into the inflatable valve stem and turn the locking thumb lever to the down position.
NOTE: Connect the appropriate valve stem adapter(s) onto the air hose nozzle (if needed.)
3. ENSURE that the air hose nozzle and the valve stem adapter (if used) are properly seated onto/into the inflatable valve stem.
NOTE: Insert the air hose nozzle with the valve stem adapter (if needed) into or onto the inflatable air valve stem as far as practical.
4. Press the compressor power switch to the ON (I) position.
5. Monitor the pressure on the compressor air pressure gauge. When the desired pressure is reached, Press the compressor power switch to the OFF (O) position. Unlock the
air hose nozzle thumb lever to the UP position.
6. Recap the inflatable air valve stem.
7. Stow the air hose back into the Power Portable Source storage compartment.
B. TO INFLATE TYRES:
1. Remove the valve cap from the tire air valve stem.
NOTE: ENSURE that the air hose nozzle locking thumb lever is in the up position. If necessary, use valve stem adaptor.
2. Insert the compressor air hose nozzle onto the tire air valve stem, make sure that the nozzle is pushed onto the tire air valve stem as far as possible and is seated
properly. Press down the locking thumb lever to engage as shown in the illustration.
3. Press the compressor power switch to the ON ( I ) position.
NOTE: In the event that the tire is completely flat, raise the vehicle using a recommended rated jack and jack stands before inflating the tire.
4. Monitor pressure on the compressor air pressure gauge.
NOTE: It is recommended to use a separate air gauge to check the actual tire inflation pressure.
5. Press the compressor power switch OFF ( O ) when the desired tire air pressure is reached.
6. Disconnect the air hose nozzle from the tire valve stem by lifting the locking thumb lever to the Up position. (Also, remove any air hose nozzle adapter, if any).
7. Recap the tire air valve stem. 8. Stow the air hose back into the Portable Power Source storage compartment.
CHARGING & RECHARGING INSTRUCTIONS
WARNING: Do not overcharge this unit. Prior to Charging unit, read and understand all instructions listed below. Overcharging may result in damage to the
unit.
CAUTIONS:
▪ ENSURE that the unit power switches are in the OFF ( O ) positions.
▪
Recharge the Portable Power Source in a clear, unobstructed open area.
▪
DO NOT recharge the Portable Power Source near flammable materials or any location which accumulate flammable fumes.
▪
DO NOT smoke, use matches, lighters or open flame near the Portable Power Source when / during recharging.
▪
This product may arrive partially charged from the manufacturer. It is recommended to fully charge the unit immediately after purchase and before using for
the first time. Fully recharge the Portable Power Source, when Red LED is illuminating.
▪
The charging LED indicator will be illuminated while charging. When charging the RED LED will change colour to AMBER (75% of charge) and finally to GREEN
(fully charged). This light will not go out until the charging plug is removed.
▪
Do not charge the Portable Power Source for more than 48 hours continuously.
▪ Make sure that any electrical outlet, located in a potentially wet or moist area, and is to be used to charge the Portable Power Source, is protected by a
Ground Fault Interrupt switch.
Locking thumb lever
Air hose nozzle
Tire air valve system