Campingaz CAMP'BISTRO DLX Instrucciones De Empleo página 9

Cooking
Position the pan on the arms centred over the burner
and adjust the gas flow so that the flames do not burn
higher than the pan.
The size of the flame can be regulated by turning the
ignition knob (1) between the full flow position (MAX)
and minimum flow position (MIN) (fig. 8).
Extinguishing
Turn the ignition knob (1) clockwise to "l" position (fig. 9).
D - CHANGING THE CARTRIDGE
The cartridge may be removed even if it is not empty.
Once your stove has fully cooled:
- Check that the gas inlet is fully closed by turning the
control knob (1) clockwise to the "l" position (Fig. 9)
and that the burner (5) is extinguished.
- Disconnect the cartridge by putting the lever (2) in the
"UNLOCK" position (fig. 10).
- Open the cartridge compartment (3) and remove the
cartridge by lifting it from behind.
- Never throw away a cartridge which is not completely
empty, (check there is no liquid in the cartridge by
shaking it).
- Make sure that no food has dropped into and thus
obstructs the stove regulator internal housing (fig. 4)
before installing a new cartridge.
- Check that the seal is present and in good condition
(fig. 4)
- Put in a new cartridge by following the instructions
in section "B - PREPARATION FOR OPERATION -
Installing a CAMPINGAZ
Caution: If the cartridge is replaced while the stove is in
use, do not touch the hot surfaces of the stove (burner,
saucepan holder, plate...).
Caution: Gas residue may remain in the stove after the
stove has been turned off. For your safety, with the
cartridge lever (2) in "UNLOCK" position, turn ignition
knob (1) to ( ) position to burn off any remaining fuel.
E - SAFETY DEVICE
Do not use a stove which is leaking, damaged, or which
does not operate properly. If the gas pressure in the
cartridge is too high, a built-in device disconnects the
cartridge and the lever (2) returns to "UNLOCK". In this
case, you need to remove the cartridge and let it cool
down (run it under water, for example) before reusing
it or use a new cartridge following the instructions in
Section "D - CHANGING THE CARTRIDGE".
The stove will not operate until the gas pressure of the
cartridge returns back to the normal.
HOW TO RESET SAFETY DEVICE
- Turn the ignition knob (1) to the "l" position and raise
cartridge lever (2) up to the "UNLOCK" position.
- Remove the gas cartridge.
- Turn the ignition knob to the (
excess gas in the gas cock.
- After 5 minutes, turn the ignition knob to the "l" position.
- Make sure the ignition knob is "l" and reset safety
device by:
a) Pushing the cartridge lever down to "LOCK" position, and then
b) Pushing the cartridge lever up to "UNLOCK" position.
- Replace a new cartridge or a cooled down cartridge.
- Repeat the ignition procedure.
If the temperature in the cartridge is high initially, fuel will
not emerge even though the cartridge is installed in the
stove. This is due to the operation of the safety device.
cartridge CP250/ CP250 SP".
®
) position to release
It is not out of order.
F - CLEANING AND STORAGE
In case of burn back (ignition under the burner
cap) switch the stove off, allow it to cool down
(approximately five minutes), then reignite the stove.
If the problem of burn back persists, then please
contact your local Campingaz
Once your stove has fully cooled:
1 - Cleaning
Main stove
- Clean the stove having removed the cartridge.
- Clean the pan support (4) and the cartridge exterior
and cover (3) with warm water, then dry with a cloth.
Burner (5)
A dirty burner will clog the holes of the flame.
Clean the flame holes of burner head with a metal brush
Piezo ignition electrode (6)
If the electrode gets wet, the stove will not light. Make
sure any water is removed, and dry with a cloth.
Stainless Steel:
Stainless steel is known for its ability to resist corrosion
and rust. However, dirt, dust, grime and non-appropriate
cleaners put stainless steel at risk for corrosion and
rust. Stainless steel responds well to cleaning as long
as certain rules are followed
DO :
y Read carefully the instructions on the cleaning
products and make sure it's appropriate for stainless
steel. Ideally, use specific stainless steel cleaners.
Pay special attention to some of them which can be
inappropriate for paints, these look like aluminium or
stainless steel and can erase markings.
y Use a safe, non-abrasive sponge. Brush in the
direction of the grain of the metal.
y Rinse thoroughly.
y Always dry the surface with a soft towel or cloth. A
microfibre towel is preferable.
DON'T :
y Never leave wet sponges, cloths, or cleaning pads
on the Stainless steel surface.
y Never leave solutions of chlorine bleach and water
on your Stainless steel surface. Chlorides, which
are found in most soaps, detergents, bleaches, and
cleansers, are very aggressive to stainless steel.
y Never use oven cleaners that contain caustic
chemicals.
y Do not use paper towel or scratch-sponges.
2 - Storage and transportation
- Check that the lever (2) is in the UNLOCK position
(Fig. 10).
- Always remove the gas cartridge from the stove
during storage or transportation.
- Store the stove and the cartridge in a cool, dry and
well-ventilated area, out of reach of children. Never
store in a basement or cellar.
9
representative.
®
GB