Publicidad
Idiomas disponibles
Idiomas disponibles
SPLCS-12A
SPLCS-12L
SPLCS-12V
SPLCS-24A
SPLCS-24L
SPLCS-24V
SPSCS-12A
SPSCS-12L
SPSCS-12V
®
Opt-X
Splice Module
© 2013 Leviton Manufacturing Co., Inc.
Customer Support: 800.824.3005
International: +1.425.486.2222
Web:
www.leviton.com
Installation Instructions
IMPORTANT INSTRUCTIONS
1. Read and understand all instructions. Follow all warnings and instructions marked on the product.
2. Do not use this product near water-e.g., near a tub, wash basin, kitchen sink or laundry tub, in a wet basement, or near a swimming pool.
3. Never push objects of any kind into this product through openings, as they may touch dangerous voltages.
SAVE THESE INSTRUCTIONS.
4.
SAFETY INFORMATION
1. Never install communications wiring or components during a lightning storm.
2. Never install communications components in wet locations unless the components are designed specifically for use in wet locations.
3. Never touch uninsulated wires or terminals unless the wiring has been disconnected at the network interface.
4. Use caution when installing or modifying communications wiring or components.
Leviton and Leviton Block & Design are trademarks of Leviton Manufacturing Co., Inc. and are registered trademarks in many countries throughout the world.
DESCRIPTION
The Leviton Opt-X Splice Module can accommodate either 12 or 24 single fusion fiber terminations. The module is available in either LC or SC for 12 fiber applications and LC for
24 fiber applications.
Warning: Always wear eye protection when handling optical fibers. Dispose of any cut or cleaved ends properly.
INSTALLATION
The following installation instructions describe the assembly procedure for the new Opt-X Splice Module which allow for fusion splice termination on 250um, and 900um fiber/cable.
DI-00X-SPLCS-20B
Publicidad
Tabla de contenido
Manuales relacionados para Leviton Opt-X SPLCS-12A
Resumen de contenidos para Leviton Opt-X SPLCS-12A
- Página 1 Leviton and Leviton Block & Design are trademarks of Leviton Manufacturing Co., Inc. and are registered trademarks in many countries throughout the world. DESCRIPTION The Leviton Opt-X Splice Module can accommodate either 12 or 24 single fusion fiber terminations. The module is available in either LC or SC for 12 fiber applications and LC for 24 fiber applications.
- Página 2 3.8 Place the splice deck and base with the rear of both Leviton Opt-X Ultra (part number 5RxUH) and Opt-X 1000i facing each other. (See Figure 5) When terminating the 12- (part numbers 5R1UM-S03, and 5R2UM-S06) enclosures...
-
Página 3: Directives Importantes
DESCRIPTION Les modules d’épissage Opt-X de Leviton acceptent 12 ou 24 terminaisons simples par fusion. Ils sont offerts en versions LC ou SC (12 fibres) ou encore LC seulement (24 fibres). Avertissement : il faut toujours porter des lunettes de sécurité lorsqu’on manipule des fibres optiques. Les bouts coupés ou clivés doivent en outre être éliminés de la manière appropriée. - Página 4 Méthode d’installation dans un logement 3.6 Placer le ou les groupes de fibres de liaison à l’extérieur de la patte de retenue latérale de la base (figure 1). 1.0 Les modules d’épissage Opt-X sont conçus de façon à ce qu’on puisse effectuer les opérations d’installation et de 3.7 Faire sortir les fibres de liaison de la base.
-
Página 5: Instrucciones Importantes
DESCRIPCION El Módulo de Empalme Opt-X de Leviton tiene la capacidad de acomodar fusiones de terminaciones de 12 o 24 fibras sencillas. El módulo está disponible en aplicaciones LC o SC para 12 fibras y LC para aplicaciones de 24. - Página 6 Módulo de empalme Opt X de 12 - fibras, coloque la cubierta del empalme aproximadamente a 23 cm (9 Las cajas Opt-X Ultra de Leviton (número de parte 5RxUH) y pulgadas) en la parte posterior y en paralelo con la base. Para el Opt-X 1000i (números de parte 5R1UM-S03 y 5R2UM-S06)