Worx Nitro WG751 Manual De Instrucciones página 16

No light is
illuminated.
Only one light is
flashing twice per
cycle.
Only one light
is flashing three
times per cycle.
Only one light is
flashing four times
per cycle.
MULCHING MOWING TIPS
When using the mulching plug, your new mower is
designed to cut the grass clippings into small pieces and
distribute them back into the lawn, using mulching fins
located inside the mower deck.
Under normal conditions, the mulched grass will
biodegrade quickly to provide nutrients to the lawn. Please
review the following recommendations for optimum
mulching performance,
16
1) Avoid mowing when the grass is wet from rain
or dew. Wet grass may form clumps which
interfere with the mulching action and reduce
runtime. The best time to mow grass is in the
late afternoon when the grass is dry and the
newly cut area will not be exposed to direct
sunlight.
2) For best mulching performance, set the cutting
height to remove about one third of the grass
blade length, ideally no more than 1.5" inches
at one time. If the lawn is overgrown, it may be
necessary to increase the cut height to reduce
the pushing effort and prevent overloading
the motor. For extremely heavy mulching, it is
advisable to first cut at a high cut height setting,
and then re-cut to the final cut height. Otherwise,
make narrower cuts and mow slowly.
3) For best performance, keep the mower housing
free of built-up grass. From time to time turn
off mower and wait for the blade to come to a
complete stop. Then unplug the Safety Key(6)
and turn mower on its side. Using an object such
as a stick, wipe out any accumulation of grass
in the blade area. Be careful of the sharp edges
of the blade. Clean often in wet, new grass, and
always after every use.
4) Certain types of grass or grass conditions may
require that an area be mulched a second time
to fully disperse the grass throughout the lawn.
If cutting a second time, it is advisable to cut
perpendicular (across) the first cut pattern. DO
NOT CHANGE CUT PATTERN IN ANY WAY THAT
3-in-1 Cordless Lawn Mower
At least one battery is not fully
installed or battery may be
defective.
At least one battery is over
discharged (please refer to
the battery charge condition),
please recharge the two bat-
teries at once before use again
or storage.
At least one battery is hot,
wait for them cool down
before start again.
The machine is over load.
Raise the cutting height or
push slowly.
WOULD CAUSE MOWING DOWN A HILL.
5) Change your cutting pattern from week to week.
This will help prevent matting and graining of
the lawn.
CUTTING AREA
The cutting area can be affected by many factors
including: cutting height, operation practices (ex: starting/
stopping), lawn moisture levels, grass length and
thickness.
It is ideal for mowing ¼ acre to 1/2 acre lot sizes.
TIPS:
1) Mowing the lawn frequently and reducing the amount
of starting/stopping procedures will help conserve
battery runtime. It is recommended to always use the
same two batteries during operation with fully charged
levels.
2) For the best cutting performance, it is recommended
to only mow up to 1/3 or less of the current grass height
at a time. Mow at a slower pace when cutting long/
thick grass to allow the mower to properly discharge the
clippings.
MAINTENANCE
WARNING: Stop the mower and remove
the safety key before removing the grass
collection bag.
NOTE: To ensure long and reliable service, perform
the following maintenance procedures regularly. Check
for obvious defects such as a loose, dislodged or a
damaged blade, loose fittings, and worn or damaged
components. Check that the covers and guards are
all undamaged and are correctly attached to mower.
Carry out any necessary maintenance or repairs before
operating mower. If the mower should happen to fail
despite regular maintenance, please call our customer
helpline for advice.
BLADE SHARPENING
KEEP BLADE SHARP FOR BEST MOWER
PERFORMANCE. A DULL BLADE DOES NOT CUT
GRASS CLEANLY OR MULCH PROPERLY.
WEAR PROPER EYE PROTECTION WHILE
REMOVING, SHARPENING, AND INSTALLING
BLADE. ENSURE THAT SAFETY KEY IS REMOVED.
Sharpening the blade twice during a mowing season
is usually sufficient under normal circumstances.
Sand causes the blade to dull quickly. If your lawn
has sandy soil, more frequent sharpening may be
required.
REPLACE BENT OR DAMAGED BLADE
IMMEDIATELY.
WHEN SHARPENING THE BLADE (See Fig. N)
1. Make sure blade remains balanced.
2. Sharpen blade at the original cutting angle.
3. Sharpen cutting edges on both ends of blade to
keep it balanced, removing equal amounts of
material from both ends.
EN