Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
HOW TO SET SYSTEM LEVEL
Installer, homeowner, or building science expert may adjust Broan
SmartSense
ventilation system level.
®
1. System Level is only set in Master control. If home has more than
one installation then locate Master control; it is usually in master
bathroom or it should be clearly marked or documented.
2. Circle, mark or highlight System Level in Table A using home's
square footage and number of bedrooms.
Note: Building science experts may calculate different rate based
on air infiltration measurements.
3. Circle, mark or highlight same System Level in Table B.
4. If home's System Level is 30 then next steps are not necessary,
since System Level is set at factory to 30.
5. Put Master control in Program mode; press and hold SET button
for 3-seconds and then release it.
6. LED should be turning on and off every second (slow-blink); if it
is not then repeat step 5.
7. Press and release (tap) On paddle number of times from Table B.
If you tap On paddle too many times, tap Off paddle and System
Level will be reduced once for each Off paddle tap.
In order to reset System Level to 30, immediately after entering
Program mode (Steps 5-6), tap On paddle only once and then tap
Off paddle only once.
If you lose On paddle counts, tap Off paddle 9 times or more then
tap On paddle twice; System Level will be at 30; proceed with On
paddle taps from Table B.
8. Exit Program mode; press and release SET button.
9. After exiting Program mode, LED will fast-blink a number of
times.
LED will fast-blink the same number of times in three sets with a
slight pause in between each set.
10. Count number of times LED fast-blinks in a set.
11. Compare number of times LED fast-blinks in a set to number for
System Level in Table B.
12. If they are the same then System Level is set accordingly;
otherwise, re-adjust System Level starting with step 5.
FEATURE SELECTIONS
Vacation Mode: Used only with Master control. Temporarily disables
Broan SmartSense
system. Master control will not automatically
®
turn on its fan or any other system fan. After Feature Selection
mode exit, Vacation mode is cancelled when Master control On
paddle is pressed.
Disabled Mode: Excludes fan from automatic ventilation usage.
Does not affect manual operation and its ventilation is credited
toward system level accumulation. Master control will not turn it on
for automatic ventilation requirement fulfillment. If Master control
is put in Disabled mode, it will not turn on any fans for automatic
ventilation and recommended indoor air quality ventilation level is
not assured.
Automatic-Off: Automatically turns fan off 60-minutes after it was
manually turned on.
Delayed-Off: Turns fan off 20-minutes after Off paddle was pressed
once. In order to turn fan off immediately, press Off paddle twice.
HOW TO NAVIGATE FEATURE SELECTION MODE
Refer to diagram. First, make sure fan and LED are off by pressing
and releasing Off paddle. Vacation/Disabled Feature Selection
mode entry is accomplished by pressing On paddle until LED turns
on and off every second (slow-blink). Automatic-Off/Delayed-Off
Feature Selection mode entry is accomplished using same method
with Off paddle. Once either Feature Selection mode is entered,
pressing and holding associated paddle displays Feature's status
using LED. Press and release associated paddle to toggle feature on
or off. When finished, press and release SET button to exit Feature
MODELS SSQTXE080 • SSQTXE110
TABLE A
Floor Area (ft
)
2
0 - 1
< 1500
_
30
1501 - 3000
45
3001 - 4500
60
4501 - 6000
75
6001 - 7500
90
> 7500
105
ON PADDLE
TABLE B
System
ON
Fast
Level
Taps
Blinks
165
9
11
150
8
10
135
7
9
120
6
8
105
5
7
90
4
6
75
3
5
60
2
4
45
1
3
30
ON &
2
OFF or
OFF 9x
& ON 2x
Feature Selection Modes
If fan is on, press OFF paddle.
Press and hold paddle (approximately 10-seconds)
until LED displays slow-blink then release.
ON Paddle
Vacation
or
Disabled
Press and hold paddle to display Feature status.
Press and release paddle to toggle Feature on or off.
ON
OFF
Paddle
Paddle
Vacation
Disabled
When done, press and release SET button;
LED and fan should turn on and then off.
Bedrooms
2 - 3
4 - 5
6 - 7
45
60
75
60
75
90
75
90
105
90
105
120
105
120
135
120
135
150
Push to
turn ON
LED
S
S
mart
ense
Push to
turn OFF
SET
button
OFF Paddle
Automatic-Off
or
Delayed-Off
ON
OFF
Paddle
Paddle
Automatic
Delayed
-Off
-Off
Page 3
> 7
90
105
120
135
150
165
®
®
OFF
PADDLE
Publicidad
Tabla de contenido
