Broan SmartSense SSQTXE080 Guia De Inicio Rapido página 4

Selection mode. Fan and LED will turn on for one to two seconds
and then turn off.
1. Make sure fan and LED are off; press and release Off paddle.
2. Put control in Feature Selection mode; press and hold On or Off
paddle (approximately 10-seconds) until LED turns on and off
every second (slow-blink).
3. Release paddle.
4. Press and hold On or Off paddle with Feature associated;
Feature status is displayed when LED is steady. Feature is off if
LED is off. Feature is on if LED is on.
5. Release paddle and LED returns to slow-blink.
6. Press and release paddle to toggle Feature on or off.
7. Check Feature status by repeating steps 4 and 5.
8. When done with Feature Selection mode, press and release SET
button.
9. Fan and LED turn on for 1 to 2-seconds and then turn off;
this action confirms new setting is stored and Feature Selection
mode exit.
Feature Selection mode will automatically exit if any paddle is
not pressed within 3-minutes.
HOW TO LINK TO OTHER INSTEON™
(NON-LINKLOGIC™) DEVICES
SmartSense controls can turn other INSTEON™ enabled devices
®
on and off and other INSTEON™ devices can turn SmartSense
controls on and off.
1. Put controller device in link mode; refer to device's installation
instructions.
If SmartSense control is selected as controller then push and
hold On paddle (approximately 10-seconds) until LED turns on
and off every second (slow-blink). Release On paddle.
2. Go to controlled device and create link according to device's
installation instructions. For SmartSense control, press and
hold SET button. Continue holding SET button for 3-seconds
then release it. Within 2-seconds, fan and LED turn on; stay on
for 1 to 2-seconds and then turn off.
3. If devices and/or controls do not respond as described, repeat
process beginning with step 1.
HOW TO REMOVE SMARTSENSE
INSTEON™ INDIVIDUAL LINKS
Links are two-way communication pathways between devices. It is
important to remove both ends of a link. The following "Remove"
procedure accomplishes this task.
1. On Master control, push and hold Off paddle.
2. W ait (approximately 10-seconds) until LED turns on and off
every second (slow-blink).
3. Release Off paddle.
4. On other control, press and hold SET button.
5. Continue holding SET button for 3-seconds then release it.
W ithin 2-seconds, fan and LED turn on; stay on for 1 to
2-seconds and then turn off.
6. If control does not respond as described, repeat process
beginning with step 1.
HOW TO CHANGE CONTROL COLOR
An almond paddle/frame assembly is included.
1. U se magnetic #1 Philips screwdriver and remove (4) screws
from white paddle/frame.
®
, LINKLOGIC™, AND
®
MODELS SSQTXE080 • SSQTXE110
2. Remove white paddle/frame from control.
C aution: Do not touch or put anything inside control housing;
control damage may result.
3. Place almond paddle/frame on control.
4. Replace (4) screws and lightly tighten them.
Caution: Do not over tighten screws; frame may crack.
RESTORING POWER TO CONTROL
Control stores all settings in nonvolatile memory; so they are not lost
when power is removed. After power loss, control will automatically
return fan to its state (on or off) before power was interrupted.
HOW TO RESTORE CONTROL FACTORY SETTINGS
This "Restore" procedure clears control's nonvolatile memory. It
returns control to how it was shipped from factory. All Feature
selections are turned off and all links are removed. "Restore"
procedure should be used cautiously; usually it is used only when
first setting up a system or for single unit installations.
Links are unique for each device pair. If one end of the link is
removed, it is important to remove the other end. "Restore" only
removes links within its control. Other link-end needs to be removed
in other device.
CAUTION: Before continuing, choose one of following options: (a)
remove links to target "Restore" control using procedure described
in "How To Remove Specific Individual Links" or (b) "Restore"
all controls in system and "Restore" all other LinkLogic™ and
INSTEON™ devices; then links need to be reestablished using
"How To Link SmartSense
®
1. R emove power from control's microcontroller; either: (a)
turn circuit breaker off or (b) pull SET button until it is
fully extended.
2. Wait 15-seconds.
3. Press and hold SET button.
4. F or option (1a), turn circuit breaker on while SET button is
pressed. For option (1b), push in and press SET button in
one motion.
5. C ontinue holding SET button for 3-seconds after power is
applied then release it.
W ithin 2-seconds, fan and LED turn on; stay on for 1 to
2-seconds and then turn off.
6. I f control does not respond as described, start process over
with step 1.
SCREWS
System" procedure.
PADDLE / FRAME
ASSEMBLY
Push to
turn ON
®
SCREWS
S S
mart ense
®
Push to
turn OFF
Page 4
99044387A