Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
BRACKET
TRUNK
PAN
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 24754F
Wrenches: 10mm, 11/16"
Drill Bits: 15/32 (.469)
DRILL HOLE
REMOVE SPARE TIRE
BEFORE DRILLING
j
Qty. (4)
Carriage Bolt 7/16-14 X 1.50
k
Qty. (5)
Flat Washer 7/16
l
Qty. (5)
Lock Washer 7/16
m
Qty. (5)
Hex Nut 7/16-14
1.
Remove spare tire. Remove the drain plug from the passenger side of the trunk.
2.
Put the angle bracket (1) with carriage bolt (Item 1) over the existing drain hole inside the trunk setting against the bottom and back of the trunk
pan.
3.
Raise the hitch into position under the angle bracket and attach the fasteners as shown. Hand tighten the hitch to angle bracket fasteners.
4.
Align the hitch into position using the back of the trunk pan and the rib running along the trunk pan with the location of the hole on the hitch
bar. Check the location of the hitch on the vehicle. Note: center rib on trunk pan not center of vehicle.
5.
Drill the hole thru the rib and into the trunk using the hitch as a template. Secure the hitch using the fasteners as shown.
6.
Drill a hole using the hitch as a template into the trunk pan on the drivers side of the vehicle. Repeat step 2. Hand tighten all fasteners.
7.
With the hitch in position and both angle brackets setting against the rear of the trunk pan drill the holes thru the rear of the trunk pan using the
angle brackets as a template. Place the (2) remaining (Item 1) Carriage bolt through the angle brackets.
8.
Remove the (2) bolts with the 10mm wrench and push the fascia out of the way to allow access to the rear of the trunk pan and fastener.
Attach the fasteners as shown.
9.
Tighten all 7/16 fasteners with torque wrench to 50 Lb.-Ft.
10.
Seal drilled or existing drain holes in trunk pan to prevent intrusion of exhaust fumes and water
11.
Reinstall the spare tire in the trunk and re-attach the fascia.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005, 2010, 2015 Cequent Performance Products – Printed in Mexico
Installation Instructions
MITSUBISHI ECLIPSE
FASCIA
ANGLE
BRACKET
DRILL
HOLES
n
o
p
q
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB Max Gross Trailer Weight
200 LB Max Tongue Weight
Wiring Access Location: PC3 , PC4
DRILL HOLE
Qty. (1)
Carriage Bolt 7/16-14 X 2.50
Qty. (1)
Block 1 x 2
Qty. (2)
Block 1 x 2
24754N
Part Numbers:
24754, 77130,
60813, 24842
U-Haul
(Sold separately)
Drawbar Kit:
3597
6806
Drawbar must be used in the
RISE position only.
10-13-15
Rev. D
Publicidad
Manuales relacionados para Cequent Performance Products 24754
Resumen de contenidos para Cequent Performance Products 24754
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2005, 2010, 2015 Cequent Performance Products – Printed in Mexico Sheet 1 of 3...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spé cifications en matiè re de sé curité des systèmes d’attelage. Feuille 2 de 3 24754N 10-13-15 Rév. D 2005, 2010, 2015 Cequent Performance Products - Imprimé au Mexique...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulació n V-5 y SAE J684. Hoja 3 de 3 24754N 10-13-15 Rev. D 2005, 2010, 2015 Cequent Performance Products - Impreso en México...