Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 24768F
Wrenches: 10mm, 11/16
Drill Bits: None
j
Qty. (4)
7/16 X 1.50 GR5 Carriage Bolt
k
Qty. (4)
3/16 X 1.00 X 2.00 Block
l
Qty. (4)
Conical Toothed Washer
1.
Lower vehicle exhaust by removing the inboard and outboard exhaust hangers.
2.
Remove the exhaust heat shields from both sides of the vehicle.
3.
Enlarge the access holes in the vehicle to accept the 3/16 X 1.00 X 2.00 block.
4.
Fishwire blocks and carriage bolts through the frame rails into the existing holes in the vehicle.
5.
Raise hitch into position and install conical toothed washers and 7/16 hex nuts.
6.
Reinstall the exhaust heat shields between the hitch and the exhaust using the M6 fasteners provided (if installed correctly the
7/16 carriage bolts will fit through existing holes in the vehicle heat shields).
7.
Reinstall the vehicle exhaust.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2006, 2015 Cequent Performance Products, Inc. - Printed in Mexico
Installation Instructions
Acura TSX
Fascia
(Sold separately)
Drawbar Kit:
3593
Drawbar must be used in the
Rise position only.
Access Hole
Heat Shield
Tighten all 7/16 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Tighten all M6 CL8.8 fasteners with torque wrench to 8 Lb.-Ft. (7 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB Max Gross Trailer Weight
200 LB Max Tongue Weight
Wiring Access Location: PC3
Access Hole
Frame Rail
m
Qty. (4)
7/16 Hex Nut
n
Qty. (8)
M6 X 1.00 X 25mm CL 8.8
Sheet 1 of 3
24768N
Part Numbers:
24768
77144
60831
Heat Shield
10-13-15
Rev. B
Publicidad
Manuales relacionados para Cequent Performance Products 24768
Resumen de contenidos para Cequent Performance Products 24768
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24768N 10-13-15 Rev. B 2006, 2015 Cequent Performance Products, Inc. - Printed in Mexico...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spé cifications en matiè re de sé curité des systè mes d’attelage. Feuille 2 de 3 24768N 10-13-15 Rev. B 2006, 2015 Cequent Performance Products, Inc. Imprimé au Mexique...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulació n V-5 y SAE J684 Hoja 3 de 3 24768N 10-13-15 Rev. B 2006, 2015 Cequent Performance Products, Inc. - Impreso en México...