Cequent Performance Products 75882 Instrucciones De Instalación

Hitch Shown In Proper Position
Equipment Required: N/A
Fastener Kit: 75882F
Wrenches: 16mm, 3/4", T-30
½"-13 nut plate
1 Qty. (2)
½"-13 X 1.50 GR5 Hex Bolt
Qty. (2)
2
½" Conical Washer
3 Qty. (4)
½"-13 X 2.25 Gr. 5 Carriage Bolt
Qty. (2)
4
¼" X 3.00 X 1.00 Spacer Block
Qty. (4)
5
5/8" X 2.0 X 1.5 Spacer Block
Qty. (2)
6
½"-13 Hex Nut
Qty. (2)
7
1. Lower spare tire.
2. Remove (8) torque head screws (4 on top, 4 on bottom) which attaches the bumper fascia to the bumper under structure.
3. Raise hitch into place as shown.
(Hint, raise one side of the forward attachment above leaf spring, then repeat on the other side)
Slide nut plate into the frame from the front of the vehicle as shown and hand tighten ½" bolts into place.
4.
Remove rubber grommets and using the fish wire insert the two 7/16" bolts and two ½" bolts into their respective position.
5.
Attach middle 7/16" bolts to hitch and hand tighten.
6.
Slide 5/8" spacer blocks into place and pass ½" bolt through block and vehicle rearward slot as shown. Hand tighten.
7.
8. Tighten all hitch fasteners to the torque specifications given.
9. Reinstall bumper fascia and raise spare tire into place
Note: Check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
©
2014 Cequent Performance Products, Inc
Installation Instructions
Ram Promaster
Except Extended Model
Bumper
Torque Head
Screws
Frame
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
Do Not Exceed Lower of Towing Vehicle
Hitch Type
Weight Distribution
Weight Carrying
Ball Mount
Figure 1
7/16"-14 x 1.75 Carriage Bolt
8 Qty. (2)
1/4" X 3.00 X 1.00 Spacer Block
Qty. (2)
9
7/16" Conical Washer
10 Qty. (2)
7/16"-14 Hex Nut
Qty. (2)
11
½" Fish Wire
Qty. (2)
12
7/16" Fish Wire
Qty. (2)
13
Tighten all 7/16"-14 Gr. 5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Tighten all ½"-13 Gr. 5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
SAE J684.
Sheet of 3 1 75882N
Part Numbers:
75882
87655
44706
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
7500
6000
Accessory Rating
Wiring Access Location: SUV 3&4
Note: Fasteners typical
both sides of hitch.
2-10-14
Form F206 Rev A 5605
Max Tongue
WT (LB)
750
750
D
Rev. B