Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame rail
Hitch Shown In Proper Position
Equipment Required: Pull wires (provided)
Fastener Kit: 75852F
Wrenches: 11/16" & 3/4"
Drill Bits: None
Access
hole
Kink pull wire to keep
spacer independent of bolt
Access
hole
56
1 1 1 1
Qty. (2)
Carriage bolt ½-13 X 1.75 GR5
2 2 2 2
Qty. (2)
Spacer 1/4" X 1-1/2" X 3"
3 3 3 3
Qty. (2)
Conical washer ½"
4 4 4 4
Qty. (2)
Hex nut ½-13
1.
Feed all spacers and carriage bolts into position using the pull wires provided in each frame rail. Leave pull wire attached. Note:
It is much easier if bolt and spacer are not engaged while inserting them into frame, refer to illustration.
2.
Raise the hitch into position, feed the pull wires though the adjacent holes on the hitch.
3.
Carefully remove pull wires. One at a time place the washer over the pull wire and use it to hold the bolt in place while carefully
removing the pull wire, then attach the hex nut.
4.
Tighten all fasteners to the required torque specification.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
© 2013 Cequent Performance Products, Inc
Printed in Mexico
Installation Instructions
Ford Transit Connect
Fascia
Frame rail
Pull wire
Access
hole 7/16"
Frame rail
2
1
Sort fasteners before installation
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Tighten all 7/16-14 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location:
Access
hole
1
2
3
4
5 5 5 5
Qty. (2)
6 6 6 6
Qty. (2)
7 7 7 7
Qty. (2)
8 8 8 8
Qty. (2)
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
4000 (1816 Kg)
3500 (1589 Kg)
SUV1,2
Note: Fasteners
typical both sides
5
Access slot for
6
7/16" fasteners
7
8
Carriage bolt 7/16-14 X 1.75 GR5
Spacer ¼" X 7/8" X 3"
Conical washer 7/16"
Hex nut 7/16-14
75852N
9-24-13
Part Numbers:
75852
87651
44702
Max Tongue
WT (LB)
400 (182 Kg)
400 (182 Kg)
C
Accessory Rating
Rev. A
Form: F205 Rev C 9-17-2012
Publicidad
Manuales relacionados para Cequent Performance Products 75852
Resumen de contenidos para Cequent Performance Products 75852
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. © 2013 Cequent Performance Products, Inc Sheet 1 of 3 75852N 9-24-13 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. © 2013 Cequent Performance Products, Inc Feuille 2 de 3...
- Página 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. © 2013 Cequent Performance Products, Inc Hoja 3 de 3 75852N 9-24-13 Rev.