Cequent Performance Products 75898 Instrucciones De Instalación

Frame rail
Rearward
Hitch Shown In Proper Position
Equipment Required: Small screwdriver, Lubricant or
soapy water, Utility knife or shears. (Drill or rotary tool)
Fastener Kit: 75898F
Wrenches: 11/16", 7/8" socket
Existing 7/8"
Diameter hole
in frame
3/8" dia. Drilled holes
Access hole modification to allow
pull wire of block and carriage bolt
Figure 2
Kink pull wire to keep
spacer independent of bolt
1 1 1 1 Qty. (6) Carriage bolt 7/16-14 X 1.50 GR5
2 2 2 2 Qty. (6) 7/16" Conical Washer
3 3 3 3 Qty. (6) Hex nut 7/16-14
1. Lower and remove spare tire from vehicle. The tire release is located inside rear cargo area in middle of floor.
2. Lower exhaust system at the rubber isolator. Spraying a lubricant on the metal hanger rod and the rubber isolator helps removal.
3. Remove the plastic rivets that fasten the fascia tabs to the vehicle. Note: Remove the center of the rivet with a flat screwdriver. Keep for re- installation. Both
sides.
4. Two options to insert fasteners into the frame rails.
(A) Feed fasteners into frame rail through the access hole over spring shackle and into to the forward hole. Leave pull wires attached. Feed the fasteners into
the rearward holes using the same technique. Both sides.
(B) Enlarge the forward hole using a drill or rotary tool to accept the carriage bolt and spacer.
6. Feed the remaining fastener (items 1 & 4) into holes at rear cross member of the vehicle. Leave pull wires attached.
7. Raise hitch into position feeding the pull wires through the adjacent slots on the hitch. Feed conical washer over pull wire, using the washer to hold the bolt in
place remove the pull wires and attach the hex nut. Tighten to hold hitch in place, repeat until all fastener are attached.
8. Reinstall spare tire on the cradle to confirm no interference with hitch.
9. Torque all fasteners to specifications below.
10. Trim fascia attachments as needed. Note: trimming is on the underside of vehicle. Reinstall fascia attachments. (Both sides)
11. Raise exhaust back into position and reattach to rubber isolator.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
©
2014 Cequent Performance Products, Inc.
Installation Instructions
Chevrolet City Express
Note: trimming of fascia tabs on the
Fascia
Fasteners typical
both sides
Access hole
Areas to be trimmed as needed
Exhaust tip
6
Tighten 7/16-14 Gr.5 with torque wrench to 50 Lb.-Ft. (68 N*M).
Nissan NV200
underside of vehicle's
Do Not Exceed Lower of Towing Vehicle Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV1, SUV2
1
4
6
2
3
Figure 1
4 4 4 4 Qty. (2) Spacer .250 X 1.50 X 3.00
5 5 5 5 Qty. (4) Spacer .250 X 1.00 X 3.00
6 6 6 6 Qty. (6) Pull Wire
Sheet 1 of 3 75898N
Printed in Mexico
Part Numbers:
75898
87662
44711
78599
Max Gross
Trailer WT (LB)
DO NOT USE WITH SPRING BARS
3500 Lb (1589 Kg) 525 Lb (238 Kg)
Accessory Rating
Optional Access hole to be enlarged if using
optional pull wire procedure. See Step 4
Spring
shackle
1
5
6
5
1
2
3
8-7-14
Form: F205 Rev C 9-17-2012
U-Haul
Max Tongue
WT (LB)
C
Leaf Spring
Rev. B