Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required: Small Philips tip screwdriver, lubricant or
soapy water, & spiral wire brush
Fastener Kit: 75894F
Wrenches: 19mm
Drill Bits: None
1 1 1 1
Qty. (6)
Hex bolt M12X1.25X35 CL8.8
Note: If necessary clean the threads to the existing weldnuts. Carefully run the M12 bolts into the weld nuts or use spiral wire brush to clean the
threads.
1.
Remove appearance panel from the drivers side, if present. Remove the plastic rivets that fasten the appearance panel to the vehicle. Using a
small Philips tip screwdriver, unscrew plastic screws when loose pull the remaining plastic rivet out. Return to owner.
2.
Lower exhaust by removing rubber isolators from muffler hangers. Spraying a lubricant or soapy water on the metal hanger rod and the rubber
isolator helps removal.
3.
Raise hitch on the passenger side over exhaust pipe and slowly rotate hitch into position.
4.
Secure hitch by loosely installing all the bolts.
5.
Center hitch on the vehicle, assuring clearance with the exhaust.
6.
Tighten all fasteners to the required torque specification.
7.
Reattach previously removed exhaust hangers.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
© 2014 Cequent Performance Products, Inc
Printed in Mexico
Installation Instructions
Kia Sedona
Fascia
2
1
Tighten all M12 CL8.8 fasteners with torque wrench to 76 Lb.-Ft. (103 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: TBD
Fasteners typical both sides
Existing
weldnuts
2 2 2 2
Qty. (6)
Conical washer 1/2
Sheet 1 of 3
75894N
Part Numbers:
75894
87658
44709
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
4000 (1816 Kg)
400 (182 Kg)
4000 (1816 Kg)
400 (182 Kg)
Accessory Rating
Frame rail
2-21-14
Rev. A
Form: F205 Rev C 9-17-2012
C
Publicidad
Manuales relacionados para Cequent Performance Products 75894
Resumen de contenidos para Cequent Performance Products 75894
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. © 2014 Cequent Performance Products, Inc Sheet 1 of 3 75894N 2-21-14 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. © 2014 Cequent Performance Products, Inc Feuille 2 de 3...
- Página 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. © 2014 Cequent Performance Products, Inc Hoja 3 de 3 75894N 2-21-14 Rev.