Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame rail
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75866F
Wrenches: 3/4, 22mm, 21mm 1-1/8"
open end wrench, & 1-1/8"
Drill Bits: None
Existing weldnut
Note: Fasteners typical both sides
1 1 1 1
Qty. (2)
Hex bolt M14 X 2.0 X 40mm CL 10.9
2 2 2 2
Qty. (2)
Lock washer 9/16"
3 3 3 3
Qty. (2)
Flat washer 9/16"
4 4 4 4
Qty. (6)
Carriage bolt ½-13 X 1-3/4" GR5
5 5 5 5
Qty. (6)
Spacer
Fasteners Typical Both Sides of Vehicle
Note: Factory Installed Steel Step Bumper and Brackets Must Be Used In Conjunction with Hitch
Note: Loosen the spare tire for ease of installment
1. Remove or trim out the cap in the step bumper.
2. Remove existing M14 bolts from end of each frame rail.
3. Lift hitch into position, locating rearmost holes in hitch under existing weldnuts in vehicle frame.
4. Install M14 bolts and conical washer, into weldnuts in vehicle frame at the step bumper attachment.
5. Install remaining fasteners as shown.
6. Tighten all fasteners to the required torque specification.
7. Re-tighten the spare tire
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
© 2013 Cequent Performance Products, Inc
Printed in Mexico
Installation Instructions
Chevrolet Silverado Pickup 1500
GMC Sierra Pickup 1500
(Requires OEM Bumper)
Note : Factory installed
steel step bumper and
brackets must be used in
conjunction with this
hitch
Frame rail
3
2
1
Tighten all ½-13 GR5 fasteners with torque wrench to75 Lb.-Ft. (102 N*M)
Tighten all M14 CL10.9 fasteners with torque wrench to 100 Lb.-Ft. (136 N*M)
Tighten all 3/4-10 GR 5 fasteners with torque wrench to 260 Lb.-Ft. (353 N*M)
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU3
4
5
8
9
6
7
6 6 6 6
Qty. (6)
Conical washer ½"
7 7 7 7
Qty. (6)
Hex nut ½-13
8 8 8 8
Qty. (1)
Hex bolt ¾-10 X 3.50 GR5
9 9 9 9
Qty. (1)
Conical washer ¾"
Qty. (1)
Hex nut ¾-10
Sheet 1 of 3
Part Numbers:
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
12,000 (5448 Kg)
6000 (2724 Kg)
Accessory Rating
Cross member and step
bumper shown in cut
view for clarity
Note : Factory installed
steel step bumper and
brackets must be used in
conjunction with this
75866N
9-26-13
Form: F205 Rev C 9-17-2012
75866
87652
44703
Max Tongue
WT (LB)
1200 (545 Kg)
900 (409 Kg)
E
hitch
Rev. A
Publicidad
Manuales relacionados para Cequent Performance Products 75866
Resumen de contenidos para Cequent Performance Products 75866
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. © 2013 Cequent Performance Products, Inc Sheet 1 of 3 75866N 9-26-13 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. © 2013 Cequent Performance Products, Inc Feuille 2 de 3...
- Página 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. © 2013 Cequent Performance Products, Inc. Hoja 3 de 3 75866N 9-26-13 Rev.