Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame
Rail
Electrical Harness
Attachment
This Area
Rearward
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75810F
Wrenches: 19 mm
Factory-Installed
Bumper Bracket
Both Sides
j
Qty. (2)
Hex Bolt M12 x 1.25 mm x 40 mm CL 10.9
k
Conical Washer 1/2"
Qty. (2)
1.
CAUTION: SUPPORT THE BUMPER STRUCTURE AS REQUIRED DURING HITCH INSTALLATION.
2.
Measure and note the clearance from bumper to bed to ensure proper positioning of bumper in Step 8.
3.
Remove three (3) existing M12 hex flange bolts from the factory-installed bumper bracket (both sides). Retain for later use.
4.
Position the bumper bracket and hitch on the outboard side of the frame rail as shown (one side at a time). Make sure the
electrical wire does not get crushed between the hitch and frame rail.
5.
Loosely reinstall the existing M12 flange bolts (removed in Step 3) through the hitch side bracket, bumper bracket, frame rail, and
three (3) rearmost existing weld nuts.
With 1/2" flat washer located between the frame rail and the hitch side bracket, loosely install 1/2" conical washer and M12 hex
6.
bolt through the remaining existing weld nut as shown.
7.
Repeat Steps 4-6 for the other side.
8.
Make sure bumper-to-bed clearance is the same as measured in Step 2 before tightening all fasteners to specification.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
© 2013 Cequent Performance Products, Inc.
Printed in Mexico
Bumper
Bracket
Installation Instructions
Bumper
Note: Fasteners typical both sides
(4) Existing M12
Weld Nuts
Both Sides
Tighten all M12 CL 10.9 fasteners with torque wrench to 130 Lb.-Ft. (176 N*M)
Chevy S10
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU3
Frame Rail
Both Sides
l
Flat Washer 1/2"
Qty. (2)
Sheet 1 of 3
75810N
Part Numbers:
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
7,710 (3500 Kg)
4,000 (1816 Kg)
Accessory Rating
(3) Existing M12
Hex Flange Bolts
10-21-13
Form: F205 Rev C 9-17-2012
75810
Max Tongue
WT (LB)
771 (350 Kg)
600 (272 Kg)
C
l
j
k
Both Sides
Rev. A
Publicidad
Manuales relacionados para Cequent Performance Products 75810
Resumen de contenidos para Cequent Performance Products 75810
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. © 2013 Cequent Performance Products, Inc. Sheet 1 of 3 75810N 10-21-13 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. ©2013 Cequent Performance Products, Inc. Feuille 2 de 3...
- Página 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. © 2013 Cequent Performance Products, Inc. Hoja 3 de 3 75810N 10-21-13 Rev.