Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
HOLES FOR RE-MOUNTING
VIBRATION DAMPENER IF EQUIPPED.
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 45297F
Wrenches: 21mm,24mm
Drill Bits:
NONE
ELETRICAL
MOUNTING TAB
1
Qty. (12)
BOLTS – M14 X 2.00 X 45MM CL 10.9
2
Qty. (24)
WASHER - CONICAL
3
Qty. (12)
NUTS – M14 X 2.00
1.
LOWER SPARE TIRE
2.
REMOVE ELECTRICAL PLUG MOUNTING BRACKET, VIBRATION DAMPENER, AND FACTORY HITCH IF EQUIPPED. (Large breaker bar may
be required).
3.
INSERT THE BOLTS AND WASHERS INTO THE FRAME.
4.
RAISE HITCH INTO PLACE AND FINGER TIGHTEN WASHERS AND NUTS.
5.
-WORKING ON ONE SIDE AT A TIME, LOOSEN THE BOLTS FROM THE BUMPER MOUNTING BRACKET TO THE BUMPER ENOUGH TO
SLIDE IN THE 3/16" SPACERS (Item 5). ADJUST THE BUMPER LOCATION BEFORE RE-TIGHTENING OF THESE BOLTS. REPEAT ON
OTHER SIDE
6.
PLACE A BLOCK OF WOOD BETWEEN NEW HITCH AND BUMPER TO SUPPORT BUMPER FOR NEXT STEP.
7.
-WORKING ON ONE SIDE AT A TIME, REMOVE THE NUTS AND BOLT PLATES ATTACHING THE BUMPER MOUNTING BRACKET TO THE
FRAME. SLIDE THE VERTICAL ATTACHMENT(ITEM 4) BETWEEN THE TWO AND RE-INSTALL THE FACTORY BOLT PLATES AND NUTS.
ADJUST THE BUMPER LOCATION BEFORE RE-TIGHTENING OF THESE BOLTS. REPEAT ON OTHER SIDE
8.
USING THE HOLE PATTERN IN THE ELECTRICAL MOUNT TAB, DRILL NEW HOLES IN THE FACTORY ELECTRICAL BRACKET AND
SECURE. FASTENERS NOT INCLUDED.
9.
TIGHTEN ALL FASTENERS
10.
RAISE SPARE TIRE.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2008, 2009 Cequent Towing Products
Installation Instructions
Ford F-250, F-350, F-450
1
2
1
2
5
Tighten all M14 fasteners with torque wrench to 115 Lb.-Ft. (156 n*m)
Tighten all M12 fasteners with torque wrench to 92 Lb.-Ft. (125 n*m)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU1,PU2
EXISTING BOLT
PLATES
2
3
2
3
4
Qty. (2)
VERTICAL ATTACHMENT PLATES
5
Qty. (4)
SPACERS – 1 X 2 X 3/16"
Sheet 1 of 3
45297N
Part Numbers:
45297
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
18,000 (8172kg)
2,500 (1135kg)
18,000 (8172kg)
2,000 (908kg)
FASTENERS TYPICAL
BOTH SIDE
INSTALL ONE
4
SIDE AT A TIME
EXISTING
NUTS
BUMPER MOUNTING
BRACKETS
3-25-09
Rev. A
Form: F205 Rev A 5-6-05
Publicidad
Manuales relacionados para Cequent Towing Products 45297
Resumen de contenidos para Cequent Towing Products 45297
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 45297N 3-25-09 Rev. A 2008, 2009 Cequent Towing Products Form: F205 Rev A 5-6-05...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 45297N 3-25-09 Rev. A 2008, 2009 Cequent Towing Products Form: F205 Rev A 5-6-05...
- Página 3 Este producto cumple con las especificaciones y requerimientos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684 Página 3 de 3 45297N 3-25-09 Rev. A 2008, 2009 Cequent Towing Products Form: F205 Rev A 5-6-05...