Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

FRAME
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 41946F
Wrenches: 13/16", 15/16"
Drill Bits: 9/16"
j
BOLT-HEX 9/16"-12 X 1.75 GR5
Qty. (10)
k
BLOCK – 3/8" X 1-1/2" X 3"
Qty. (2)
l
WASHER – FLAT 9/16"
Qty. (14)
m
WASHER – LOCK 9/16"
Qty. (10)
Enlarge existing holes to 9/16" (8 places)
1.
2.
Insert bolts, brackets, and block through existing access slots and into attachment holes as shown above, each side.
3.
Raise hitch into position and fasten with flat washers, lock washers, and nuts as shown
4.
Tighten all fasteners.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
© 2012 Cequent Performance Products, Inc
Installation Instructions
GMC Full Size Van
BUMPER
j
j
p
k
o
l
n
m
Tighten all 9/16" fasteners with torque wrench to 110 Lb.-Ft. (149 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV3, SUV4
FASTENERS ARE TYPICAL
BOTH SIDES
l m
n
j
l
n
NUT – 9/16-12
Qty. (10)
o
BLOCK – 1/4" X 1-1/2" X 2"
Qty. (2)
p
BRACKET – L.H.
Qty. (1)
q
BRACKET – R.H.
Qty. (1)
Sheet 1 of 3
41946N
Part Numbers:
41946
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
13,000 (5902 Kg)
1,300 (590 Kg)
10,000 (4540 Kg)
1,500 (681 Kg)
q
1-27-12
Form: F205 Rev B 11-11-2010
l m n
Rev. X

Publicidad

loading

Resumen de contenidos para Cequent Performance Products 41946

  • Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. © 2012 Cequent Performance Products, Inc Sheet 1 of 3 41946N 1-27-12 Rev.
  • Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. © 2012 Cequent Performance Products, Inc Feuille 1 de...
  • Página 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. © 2012 Cequent Performance Products, Inc Sheet 1 of 41946N 1-27-12 Rev.