Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 41944F
Wrenches: 13/16", 7/8",
18mm, 21mm, 22mm
Drill Bits: None
Existing nuts
Attachment
Bar (provided)
FIGURE 2
Note: All Fasteners Typical Both Sides of Vehicle
j
Qty. (2)
BOLT- M14 X 1.5 X 45mm CL10.9
k
BLOCK – 3/8" X 1-1/2" X 3"
Qty. (2)
l
BLOCK – 1/4" X 1-1/2" X 3", offset hole
Qty. (2)
m
NUT – M14 x 1.5 CL 10.9
Qty. (2)
n
Qty. (2)
BOLT - M14 X 2.0 X 60mm CL10.9
o
LOCK WASHER – 9/16"
Qty. (2)
p
BLOCK – 3/8" X 1-1/2" X 2"
Qty. (2)
1. Remove existing M14 bolts from bottom of each truck frame rail bumper bracket. Give bolts to customer.
2. Lift hitch into position, locating rearmost slots in hitch under existing weldnuts in truck frame.
3. Install new M14 bolts through lockwashers, blocks and hitch into weldnuts in truck frame.
4. Remove M12 side nuts and bolt plates at the end of the frame. Keep these for re-installation later.
5. If installing on a 2001-07 model, loosen the nuts at the bumper end of the bumper brace allowing it to swing away.
6. Place attachment bars as shown and loosely bolt to hitch. On the 01-07 models, swing brace back and fasten as shown.
7. Install remaining fasteners as shown through existing large holes in truck frame. Make sure to use thinner (1/4" x 3")
block below hitch and orient hole in block so that block lays flat against hitch when tightened.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust
fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or
attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
© 2011, 2014 Cequent Performance Products, Inc - Printed in Mexico
Installation Instructions
2500HD/3500/3500HD
Sierra & Silverado Trucks,
Classic & New Body - All
Bumper
Bracket
14
14
Existing bumper
brace 2001-2007
FIGURE 1
only
(FINE THREAD)
(COURSE THREAD)
NOT ALL FASTENERS ARE USED IN ALL APPLICATIONS
Tighten all M14 X 1.5 (fine thread) fasteners with torque wrench to 148 Lb.-Ft. (201 N*M)
Tighten all M14 X 2.0 (course thread) fasteners with torque wrench to 148 Lb.-Ft. (201 N*M)
Tighten all M12 fasteners with torque wrench to 92 Lb.-Ft. (125 N*M)
GMC & Chevrolet
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
j k l m
Existing
Fasteners
o
p
n
q
Qty. (6)
r
Qty. (10)
10
Qty. (2)
Qty. (6)
11
Qty. (2)
12
Qty. (2)
13
14
Qty. (4)
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
16,000 (7264 kg)
13,000 (5902 kg)
Wiring Access Location: PU3
Existing
Weldnut
Existing nuts
14
14
q r
10
BOLT – M12 X 1.75 X 45mm CL 10.9
CONICAL WASHER – 1/2"
LOCK WASHER – 1/2"
NUT – M12 X 1.75 CL 10
FLAT WASHER – 9/16"
NUT – M14 X 2.00 CL 8
FLAT WASHER – 1/2"
41944N
Part Numbers:
41944
96944
Max Tongue
WT (LB)
1,600 (726 kg)
1,950 (886 kg)
q
r
r
11
n
p o
12
13
FIGURE 3
11
VEHICLES WITHOUT
BUMPER
09-30-14
Rev. D
Form: F205 Rev B 11-11-2010

Publicidad

loading

Resumen de contenidos para Cequent Performance Products 41944

  • Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. © 2011, 2014 Cequent Performance Products, Inc - Printed in Mexico Sheet 1 of 3...
  • Página 2 Ne jamais utiliser une torche pour découper un accès ou un trou de fixation. Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. © 2011, 2014 Cequent Performance Products, Inc - Imprimé au Mexique Feuille 2 de 3...
  • Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. © 2011, 2014 Cequent Performance Products, Inc - Impreso en México Sheet 3 of 3...

Este manual también es adecuado para:

96944