Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 41933F
Wrenches: 3/4", 7/8"
Bumper
Bracket
RED – GRADE 8 NUT
THIS LOCATION ONLY
RED
j
Hex Bolt, 1/2-13 x 2.00" Grade 8
Qty. (2)
k
Conical Washer, 1/2"
Qty. (10)
l
Spacer, 1" x 2" x 1/4", Round Hole
Qty. (2)
m
Hex Nut, 1/2" (2 are red -grade 8)
Qty. (6)
1.
Raise hitch into position as shown in Figure 1. The bumper is not shown for clarity.
2.
Use fasteners to attach the hitch to the bumper bracket. Make sure that round holed spacers are placed between the back of
the bumper bracket and the hitch.
3.
Use pull wires to feed carriage bolts and blocks through the access holes in the sides of the frame. Position the carriage bolts
and blocks through the holes in the frame and the bracket of the hitch as shown in Figure 2.
4.
Install the remaining washers and nuts on the bolts and tighten all nuts.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
©
2005, 2009, 2012 Cequent Performance Products
Installation Instructions
Ford F-150
Lincoln Mark LT
FIGURE 1
Tighten all ½-13 grade 5 fasteners with torque wrench to 75 Lb.-Ft.
Tighten all ½-13 grade 8 fasteners with torque wrench to 110 Lb.-Ft.
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU3
Frame Rail
Hitch
Bracket
Pull
Wire
8
RED – GRADE 8 NUT
THIS LOCATION ONLY
n
Hex Bolt, 1/2-13 x 1-1/2" Grade 5
Qty. (2)
o
Carriage Bolt, 1/2-13 x 1-3/4" Grade 5
Qty. (2)
p
Spacer, 1" x 3 " x 1/4", Square Hole
Qty. (2)
q
Qty. (1)
Pull Wire
41933N
Part Numbers:
41933
96933
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
14,000 (6356 Kg.)
1,400 (636 Kg.)
12,000 (5448 Kg.)
1,200 (545 Kg.)
Frame Rail
Access Hole
FIGURE 2
6-1-12
Rev. C
Publicidad
Manuales relacionados para Cequent Performance Products 41933
Resumen de contenidos para Cequent Performance Products 41933
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. © 2005, 2009, 2012 Cequent Performance Products Sheet 1 of 3 41933N 6-1-12...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. © 2005, 2009, 2012 Cequent Performance Products Feuille 2 de 3 41933N 6-1-12...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684. © 2005, 2009, 2012 Cequent Performance Products Hoja 3 de 3 41933N 6-1-12 Rev.