Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame Rail
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 41936F
Wrenches: ¾"
Drill Bits: 17/32"
Chisel, Grinder, Clamps
Center Punch
Rivet to be
Removed this
Location –
Dodge Only
Fasteners Typical
Both Sides
j
Qty. (6)
Carriage Bolt 1/2-13 x 1.75 GR8
k
Spacer Block ¼" x 1" x 3"
Qty. (6)
Dodge Chassis Cab Models:
1.
Remove rearmost rivet on bottom of frame rail, each side. (Rivet location will be enlarged in step 3).
2.
Raise hitch into position, placing rear edges of horizontal flanges flush with end of frame rails and clamp to frame rail.
3.
Using hitch as a template, drill 3 holes each side as shown, using extreme caution when drilling near fuel filler lines on driver's
side. (Note: 1" diameter hole is a clearance hole for Chevrolet/GMC vehicles only and therefore not used for drilling).
4.
Install fasteners as shown.
Chevrolet/GMC Cab & Chassis Models:
Raise hitch into position, aligning 1" diameter hole with rivet on bottom surface of frame rail, each side and clamp in place.
1.
2.
Using hitch as a template, drill 3 holes each side as shown.
3.
Install fasteners as shown.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z
2007, 2012 Cequent Performance Products
Installation Instructions
Dodge Ram Chassis Cab 3500/4500/5500
Chevrolet Silverado 3500 Cab & Chassis*
GMC Sierra 3500 Cab & Chassis*
*-Includes Classic and New Body Styles
Rear edge of flange flush
With end of frame rail
j k
Tighten all 1/2-13 GR8 fasteners with torque wrench to 110 Lb.-Ft. (149 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: See Manufacturer's Specs.
Vehicle Crossmember
Dodge Chassis Cab Shown
l
Lock Washer 1/2"
Qty. (6)
m
Hex Nut – ½-13 GR8
Qty. (6)
Sheet 1 of 3
41936N
Part Numbers:
41936
96936
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
Do Not Use With
Spring Bars
12,000 (5448 Kg)
1,200 (545 Kg)
Vehicle Frame Rail
Clearance hole for rivet
On Chevrolet/GMC models
Typical both sides
l m
6-1-12
Form: F205 Rev A 5-6-05
Rev. C
Publicidad
Manuales relacionados para Cequent Performance Products 41936
Resumen de contenidos para Cequent Performance Products 41936
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2007, 2012 Cequent Performance Products Sheet 1 of 3 41936N 6-1-12 Rev.
- Página 2 Instructions d’installation Numéro de pièce : Dodge Ram châssis-cabine 3500/4500/5500 41936 Chevrolet Silverado 3500 cabine et châssis* 96936 GMC Sierra 3500 cabine et châssis * Longeron de châssis *- Comprend les styles Classic et New Body Ne pas excéder les spécifications du fabricant de véhicules de remorquage, ni :...
- Página 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 2007, 2012 Cequent Performance Products Hoja 3 de 3 41936N 6-1-12 Rev.