Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 41932N
Wrenches: 7/8", 21mm
Drill Bits: NONE
j
1/2"-13 X 1-3/4" GR 5 CARRIAGE BOLT
Qty. (6)
k
1/4" X 1-1/2" X 3" BLOCK
Qty. (2)
l
Qty. (6)
CONICAL TOOTHED WASHER
1.
Remove existing M14 bolts from end of each frame rail.
2.
Lift receiver into position, locating rearmost slots in receiver under existing weldnuts in vehicle frame.
3.
Reinstall existing M14 bolts through receiver and frame into existing weldnuts.
4.
Install remaining fasteners as shown.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005, 2006, 2012 Cequent Performance Products
Installation Instructions
CHEVROLET SILVERADO PICKUP
GMC SIERRA PICKUP
VEHICLES W/ AMBER TURN SIGNALS AND FACTORY
BUMPER
Tighten all M14 fasteners with torque wrench to 115 Lb-Ft . (156 N*M)
Tighten all 1/2" GR 5 fasteners with torque wrench to 75 Lb.-Ft. (156 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
m
Qty. (6)
HEX NUT
n
1/4" X 1-1/2" X 2" BLOCK
Qty. (4)
Sheet 1 of 3
41932N
Part Numbers:
41932
81587
96932
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
14,000 (6356 Kg)
1400 (636 Kg)
12,000 (5448 Kg)
1200 (545 Kg)
Wiring Access Location: PU3
6-1-12
Rev. C
Publicidad
Manuales relacionados para Cequent Performance Products 41932
Resumen de contenidos para Cequent Performance Products 41932
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2005, 2006, 2012 Cequent Performance Products Sheet 1 of 3 41932N 6-1-12 Rev.
- Página 2 No corte los orificios de acceso o de accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684 2005, 2006, 2012 Cequent Performance Products Hoja 2 de 3...
- Página 3 Ne pas découper les trous d’accès ou d’attache à l’aide d’un chalumeau. Ce produit respecte les spécifications et les conditions d’attelage d’éléments et de systèmes de remorquages de l’état de New York, V.E.S.C. Régulation V-5 et SAE J684. 2005, 2006, 2012 Cequent Performance Products Sheet 3 of 3 41932N 6-1-12 Rev.