Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame rail
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75726F
Wrenches: 10mm, 12 mm, 14mm,
17mm, small screwdriver, Phillips head
screwdriver, & 6" socket extension
Note: When stowing the spare
or flat tire, it is necessary to lift
or flat tire, it is necessary to lift
up on the rear edge of the tire
to clear hitch.
1 1 1 1
Qty. (9)
Hex Bolt – M10 x 1.25 x 30mm CL10.9
1.
If present, remove plastic appearance panels which cover driver's and/or passenger's side frame rails. Remove the plastic
rivets that fasten the fascia tabs to the appearance panel. Note: Remove the center of the rivet with a small screwdriver.
Passenger's side panel can be reinstalled. Return drivers' side panel and fasteners to owner.
2.
Remove tow hooks from each frame rail and return hooks and fasteners to vehicle owner.
3.
Remove plastic and rubber plugs from bottom of frame rail, and outside frame rails. Return to owner.
4.
Raise hitch over exhaust tip as shown. Be careful not to pinch hoses on the outside of the passenger side frame rail or scratch
fascia. Lower the exhaust if additional clearance is need. Remove excess caulking from rails if needed.
5.
Align hitch into position over existing weldnuts as shown and install fasteners to bottom of frame rails. Do not tighten. Note: the
hitch will contact a fascia tab on the passenger side at the exhaust bridge.
6.
Install remaining fasteners into the weldnuts on the outside of the frame rail. Be careful not to pinch hoses.
7.
Torque all fasteners to specifications.
8.
Reinstall the vehicle exhaust. (If required)
9.
Reinstall passenger side appearance panel.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
©
2011 Cequent Performance Products
Installation Instructions
Toyota Highlander
Fascia
2 2 2 2
2 2 2 2
1 1 1 1
Tighten all M10 x 1.25 CL10.9 fasteners with torque wrench to 42 Lb.-Ft. (57 N*M))
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV3, 4
Frame rail
Existing weldnuts in
both vehicle frame
Exhaust bridge
2 2 2 2
Qty. (9)
Conical Toothed Washer – 3/8"
Sheet 1 of 3
75726N
Part Numbers:
75726
87615
44670
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
5000 (2270 Kg)
750 (341 Kg)
5000 (2270 Kg)
750 (341 Kg)
Vehicles
heating/cooling
hoses located in
this area.
Use caution not to
pinch.
8-5-11
Rev. A
Form: F205 Rev A 5-6-05
Publicidad
Manuales relacionados para Cequent Performance Products 75726
Resumen de contenidos para Cequent Performance Products 75726
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. © Sheet 1 of 3 75726N 8-5-11 Rev. A 2011 Cequent Performance Products Form: F205 Rev A 5-6-05...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. © Feuille 2 de 3 75726N 8-5-11 Rev. A 2011 Cequent Performance Products, Inc. Form: F205 Rev A 5-6-05...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. © Hoja 3 de 3 75726N 8-5-11 Rev. A 2011 Cequent Performance Products, Inc. Form: F205 Rev A 5-6-05...