Cequent Performance Products 75728 Instrucciones De Instalación

Rail
Hitch Shown In Proper Position
Equipment Required: ½" Pull wire (Provided), Tin Snips, Lubricant
or Soapy water
Fastener Kit: 75728F
Wrenches: 3/4", 5.5mm or 7/32, 8mm
Trim both heat shields.
Leave enough to sandwich
between frame and hitch
Rubber isolator
1
Forward
4
hole
1 1 1 1 Qty. (4) Carriage Bolt ½-13 X 1.500 GR5
2 2 2 2 Qty. (4) Conical Washer
1. Lower exhaust system at the rubber isolator (3 places) leaving the rubber isolator in place on the vehicle. Spraying a lubricant
on the metal hanger rod and the rubber isolator helps removal. Be careful not to allow muffler to fall under its own weight.
2. Disconnect the fascia center support (1 screw) and carefully push it rearward toward the impact bar and out of the way.
Reinstall screw.
3. Remove both heat shields (3 screws) and a plastic insert each side. Return (4 screws) to owner.
4. Trim both heat shields as shown. Figure 2.
5. Using the kink wire (see Figure 3) method for feeding fasteners attach carriage bolt and block to the pull wire. Feed forward
fasteners into place on both rails using the access hole at the end of the frame rail. On the outside end of both rails there is a
wide notch to make this process easier. Feed rearward fasteners into location using the same method. Note: Make sure
spacer are sitting flat on the rails and not on existing weld nuts.
6. Replace trimmed heat shields using the remaining inboard fasteners and plastic insert.
7. Raise hitch into position over the exhaust. Sandwiching the heat shield between the hitch and the rail.
8. Loosely attach fasteners as shown, center hitch on vehicle and tighten fastener to 75 Lb.-Ft. (102 N*M).
9. Raise exhaust system (3) places back into position.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z 2011 Cequent Performance Products
Installation Instructions
Ford Edge Sport
Ford Edge
Sport Fascia
Frame rail
2
3 3
Figure 1
Note: Fasteners typical both sides
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV1, 2
Rubber isolator
Spray some lubricant on the rubber
exhaust hangers and then use a
screwdriver or pry bar to remove
rubber hangers. Support the
system while you remove all of
the hangers
Access hole at end
of rails
Kink Pull wire to keep spacer
independent of bolt
Figure 3
3 3 3 3 Qty. (4) Hex Nut ½-13
4 4 4 4 Qty. (4) Spacer ¼ X 1 X 3
75728N
Part Numbers:
75728
87617
44672
Max Gross Max Tongue
Trailer WT (LB) WT (LB)
4000 (1816 Kg) 525 (239 Kg)
3500 (1589 Kg) 525 (239 Kg)
Trim Here
Trim both heat shields.
As shown
Figure 2 Figure 2
8-19-11
Form: F205 Rev A 5-6-05
Rev. A