Cequent Performance Products 75838 Instrucciones De Instalación

Frame rail
Hitch Shown In Proper Position
Equipment Required:
Pull wire (Provide), screwdriver, pliers, or trim tool
Fastener Kit: 75838F
Wrenches: 21mm, 22mm, & 3/4"
Drill Bits: None
B. Align block on
A. Insert bolt and
access hole
Block into frame
Figure 3
Reverse Pull wire Method
Figure 2
j
Qty. (6) Bolt M14 X 2.0 X4 5mm CL10.9
k
Conical washer 5/8"
Qty. (6)
l
Spacer 1/4" X 1-1/2" X 2" (round hole)
Qty. (2)
m
Qty. (4) Carriage bolt ½-13 X 1.75 GR5
place the washer over the pull wire and use it to hold the bolt in place while carefully removing the pull wire, then attach
Hint: when removing pull wires
the hex nut.
1. Remove the rubber plug from bottom from both frame rails. Detach vehicle wiring plastic fasteners from around frame rail (3) places each side, using a
screwdriver, trim panel tool or pliers.
2. Remove M14 bolts on the outside of both frame rails (2) each side. Return to owner.
3. Install small bracket as shown in figure (2) with of the M14 bolts and conical washer with the fasteners supplied. Both sides.
4. Push brackets toward the rear of the vehicle and tighten fasteners to the required torque specification.
5. Attach the carriage bolts to the pull wire, feed the pull wire through the slot on the small bracket.
6. Remove the M14 bolts (1) each side from the bottom of frame rail. Install the carriage bolt and spacer into the square hole in the frame rail using the reverse
pull wire process (leave pull wire attached). See Figure 3. Assemble the remaining M14 bolt, conical washer and spacer and start the threads into bumper
bracket.
7. Raise hitch into position rotating over exhaust, be careful not to pinch or trap electrical wires. Feed ½ pull wire thru slot on hitch bracket. Slide the hitch into
position over M14 bolt and spacer fasteners on the bottom of the frame rail. Pull ½ carriage bolt thru the slot for support.
8. Carefully remove pull wire on carriage bolt thru the small bracket and hitch bracket and install conical washer and hex nut .
9. Pull remaining carriage bolt into position, carefully remove pull wire and attach conical washer and hex nut.
10. Tighten all fasteners to the required torque specification.
11. Using the cable ties secure the vehicle wiring to the forward hole on the side of the hitch bracket with the cable ties.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and
exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut
access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
© 2013 Cequent Performance Products, Inc
Printed in Mexico
Installation Instructions
Jeep Cherokee
TrailHawk model only
Fascia
Bumper
support
l
C. Pull bolt thru
block
k
j
Figure 1
Sort fasteners before installation
Tighten all M14 CL10.9 fasteners with torque wrench to 92 Lb.-Ft. (125 N*M)
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV 1, 2
Frame rail
n
o
n
Conical washer ½"
Qty. (4)
o
Qty. (4) Hex nut ½-13
p
Spacer ¼" X 1" X 2 (square hole)
Qty. (2)
q
Qty. (2) Cable tie
Sheet 1 of 3 75838N
Part Numbers:
75838
87650
44701
78577 UH
Max Gross Max Tongue
Trailer WT (LB)
6000 (2724 Kg) 600 (272 Kg)
5000 (2270 Kg) 600 (272 Kg)
Accessory Rating
Note: Fasteners typical both sides
m
p
Small
bracket
k
j
o n
m
q
9-20-13
Form: F205 Rev C 9-17-2012
WT (LB)
D
Rev. A