Product Duration; Ce Declaration Of Conformity - Nice BIG METRO Manual Del Usuario

Ocultar thumbs Ver también para BIG METRO:

Manual (4 páginas)

Contenido

página de 49

/ 49
Contenido
Tabla de contenido
Marcadores

Tabla de contenido

Idiomas disponibles

Product duration

The duration and average economic life of the product. The value of duration is

strongly affected by the fatigue index of the manoeuvres performed by the

automation: i.e. the sum of all factors that contribute to wear of the product

(see Table 1).

To establish the probable duration of your automation, proceed as follows:

01. Calculate the fatigue index by adding the percentage values of the items

present in Table 1;

02. In Graph 2 of the value just found, trace a vertical line that crosses the

curve; from this point trace a horizontal line until the "manoeuvre cycles" line is

crossed. The value determined is the estimated duration of your product.

The estimation of duration is made on the basis of the design calculations and

the test results performed on prototypes. In fact, as it is an estimate, it does not

represent any guarantee regarding the effective duration of the product.

Length

≤ 2 m

of the panel

< 150 Kg

0 %

150 - 350 Kg

10 %

350 - 550 Kg

20 %

550 - 750 Kg

30 %

750 - 900 Kg

40 %

Environmental temperature exceeding 40°C or

below 0°C or humidity exceeding 80%

Blind panel

Installation in windy area

Declaration in accordance with the Directives: 2004/108/EC (EMC); 2006/42/EC (MD) appendix II, part B

Note - The contents of this declaration correspond to declarations in the ofﬁcial document deposited at the registered ofﬁces of Nice S.p.a. and in particular to the last revision

available before printing this manual. The text herein has been re-edited for editorial purposes.

A copy of the original declaration can be requested from Nice S.p.a. (TV) I

Number: 389/BM..

Manufacturer's Name:

Adress:

Person authorised to draw up

technical documentation:

Type:

Models:

Accessories:

The undersigned, Luigi Paro, in the role of Managing Director, declares under his sole responsibility, that the product speciﬁed above conforms to the pro-

visions of the following directives:

• DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND COUNCIL of 15 December 2004 regarding the approximation of member state legi-

slation related to electromagnetic compatibility, repealing directive 89/336/EEC, according to the following harmonized standards:

EN 61000-6-2:2005, EN 61000-6-3:2007

Directive 2006/42/EC THE EUROPEAN PARLIAMENT AND COUNCIL of 17 May 2006 regarding machinery and which amends directive 95/16/EC (recasting)

• It is hereby declared that the pertinent technical documentation has been compiled in compliance with appendix VII B of directive 2006/42/EC and that

the following essential requirements have been observed: 1.1- 1.1.2- 1.1.3- 1.2.1-1.2.6- 1.5.1-1.5.2- 1.5.5- 1.5.6- 1.5.7- 1.5.8- 1.5.10- 1.5.11

• The manufacturer undertakes to transmit to the national authorities, in response to a motivated request, all information regarding the "quasi-machine",

while maintaining full rights to the related intellectual property.

• Should the "quasi machine" be put into service in a European country with an ofﬁcial language other than that used in this declaration, the importer is obli-

ged to arrange for the relative translation to accompany this declaration.

• The "quasi-machine" must not be used until the ﬁnal machine in which it is incorporated is in turn declared as compliant, if applicable, with the provisions

of directive 2006/42/EC.

The product also complies with the following standards:

EN 60335-1:2002 + A1:2004 + A11:2004 + A12:2006 + A2:2006 + A13:2008, EN 60335-2-103:2003

The product also complies, within the constraints of applicable parts, with the following standards:

EN 13241-1:2003, EN 12445:2002, EN 12453:2002, EN 12978:2003

Oderzo, 1 April 2011

6 – English

www.metalines.com

TABLE 1

2 - 3 m

3 - 4 m

4 - 5 m