CountyLine CLTS5 1/2 HP Manual Del Usuario página 8

Installation
To Install a Deep Well Pump
(CL520, CL100, 4" or Larger Diameter Cased Well)
For wells more than 25, but not exceeding 70 feet
in depth, the 1 HP convertible deep well pump is
recommended. However, the 1/2 HP deep well pump
may also be used for depths not exceeding 70 feet.
General materials needed for the convertible pumps:
• One can PVC cement (read instructions carefully)
• One roll PTFE pipe thread sealant tape
• Two 1" female PVC adapters
• Enough rigid 1-1/4" and 1" PVC pipe and couplings
to reach from bottom of well to pump (delivery pipe)
• One 1-1/4" PVC elbow
• One 1-1/4" male PVC adapter
• One pressure regulator kit (includes fittings, tubing,
and 1/4" plug)
• One pressure gauge
• Two male 3/4" PVC adapters
Reminder: All joints and connections must be airtight . A single pinhole leak will prevent the proper operation of
the pump . Use thread compound on all threaded connections unless specified otherwise .
1. Thread 1-1/4" close nipple into
foot valve. Thread the other
end of 1-1/4" close nipple into
bottom of deep well ejector. Hand
tighten, then tighten 1/4 turn with
pipe wrench.
2. The ejector has two holes in
the top of it. Confirm nozzle is
installed. Thread deep well venturi
tube (longer tube) into larger
hole until snug. Thread 1" x 5"
nipple into smaller hole. Only
hand tighten venturi tube. Hand
tighten nipple 1/4 turn with pipe/
crescent wrench.
3. Thread a 1-1/4" male PVC
adapter over the venturi tube
and into ejector. Thread a 1"
female PVC adapter onto the
1" x 5" nipple. Hand tighten
adapters 1/4 turn with pipe/
crescent wrench.
• Enough rigid 3/4" PVC pipe to reach from pump to
pressure tank to service line
• Tank tee (for diaphragm pressure tanks)
• Two 1/4" plugs
• One 1/2" drain cock
In addition to General Materials for Deep Well Pumps
• One 1-1/4" foot valve
• One 1-1/4" close nipple
• One ejector
• One 1" x 5" nipple
• One 1-1/4" female adapter
• One well seal
• Enough rigid 1" PVC pipe and couplings to reach
from bottom of well to pump (pressure pipe)
• One 1" PVC elbow
• Two 1-1/4" male PVC adapters
• One 1" x 4" nipple
4. Subtract five feet from the
depth of your well. This is the
EJECTOR total length of PVC pipe and
couplings to cement onto both
1-1/4"
1-1/4" male and 1" female PVC
CLOSE
adapters. Cement a section of
NIPPLE
PVC pipe to each adapter, then
FOOT
lower the whole assembly into
VALVE
the well, foot valve first. Firmly clamp the end of
the PVC pipes with a pipe clamp to prevent the
assembly from sliding down into well.
1" x 5"
Nipple
5. Cement as many
Venturi
couplings and
Nozzle
sections of rigid
PVC pipe on both
the pressure and
Ejector
delivery sides as
it takes to equal
the depth of your
6392 0211
well minus four
feet, then firmly
clamp the assembly
1" FEMALE
PVC
1-1/4" MALE
with a pipe clamp
ADAPTER
PVC
ADAPTER to prevent the
assembly from
sliding down into
the well. Be sure to
keep track of which
pipe is the pressure
pipe and which is
the delivery pipe.
8
1" FEMALE
PVC
1-1/4" MALE
ADAPTER
PVC
ADAPTER
To Household
Water System
Pump Priming
Tee with Plug
or Gauge
Suction Pipe
From Well
Priming
Check
Tee and
Valve
Plug
Sanitary
Well Seal
10'
Foot
Not
Min.
Valve
to
Scale
5–10'
1862 0205 SWJ