Publicidad
2. Wind tape around the socket from the
back side so it will not come loose from
the socket securing part.
3. Mountain fold all the lines on the socket
securing part and stick them using
double-sided tape (thin) ⑳ as shown.
4. Screw the LED bulb ⑯ into the socket.
5. Connect plugs ⑱ to the red and blue
conductive wires of the socket.
6. The light source is complete
3. Assembly of light source box
3. Assembly of light source box
Prepare ③ ④ ⑨×2 ⑩ ⑫・⑳
1. Using double-sided tape (thin) attach light
source box A ③ to light source box B ④.
*Pay attention to the orientation
2. Fold as shown and stick the two tabs
using double-sided tape (thin) ⑳.
3. Apply school glue to stick the light source
assembled before inside the light source
box.
4. Glue two lens retainers ⑨ to each other.
5. Glue the glued lens retainer made before
in the position of the gray circle on the
light source box.
6. Put the lens ⑫ into the lens retainer and
glue it to the lens holder ⑩. Be careful
not to get any glue on the lens!
7. The light source box is complete.
4. Assembly of drum
4. Assembly of drum
Prepare ⑦ ⑧×2 ⑪×2 ⑬
1. Cut along the pink lines using scissors.
Cut out the printed picture ⑬.
2. Insert a cut-out printed picture into each
slit in the slit board. Be careful not to mix
up the order of pictures.
3. Fold the printed pictures in the same
direction. Glue and secure them using
tape or school glue.
4. Roll out the slit board into a cylinder and
firmly glue the end tab.
5. Glue the glued large round disc ⑪ and
small round disc ⑧ to the top and bottom
of the rolled slit board.
*Make sure the small round disc ⑧ goes
on the outer side.
6. Insert the long rod into the hole of the
drum assembled before. Make sure it
penetrates the center of the drum. Next,
glue it in position.
*Make sure not to mix up the right and left
side
The side with the handle base should be
on the right.
7. The drum is complete.
5. Assembly of whole body
5. Assembly of whole body
1. Using double-sided tape (thin) ⑳ stick
base left ①, to base right ②, and to base
front ⑤ as shown.
2. Fold as shown and stick using double-
sided tape (thin).
3. Insert the drum assembled before into it
from inside.
*Make sure the drum is facing the right
way.. How to position the shaft
First pass the long rod through the hole,
and push the other end into position.
Pass the short round stick through the
other hole to complete the assembly.
4. Fold the base as shown using double-
sided tape (thin) and stick the areas
indicated. *Do the same on the other side
as well.
5. Stick the upper part using double-sided
tape (thin)
6. Connect two size AA battery holders ⑭.
Cut two 1x 3 cm. lengths of double-sided
tape (thick) ⑲ and stick them on the back
of the battery holders.
7. Stick the battery holders on the lid of
the base in the position indicated in the
diagram.
8. Cut one length of 1 x 3 cm double-sided
tape (thick) ⑲ and use it to stick the
switch ⑮ in the position indicated in the
diagram.
9. Cut the plastic conductive wire in half and
strip back the coating for about 3 cm from
the ends. Wind the bare wire ends around
the plugs ⑱.
How to remove the plastic coating from
the plastic conductive wire.
10. Connect the battery holders to the switch
using the plastic conductive wires made
before as shown.
11. Pass the red and blue plugs from the
light source through the hole on the
base.
12. Insert the protruding part of the light
source into the main body to install the
light source into the base. Place the rod
in the notch of the light source section.
13. Pass the red and blue wires and plugs
from the light source through to the
battery holders
14. Glue the short rod to the handle base
15. Glue the assembled handle to the round
rod. If the handle touches the body when
it is turned, glue it so the handle tilts a
little outward.
16. Completed Item
6. How animation works
6. How animation works
Animation (moving pictures) you see on TV
shows move very smoothly. Still pictures that
have small differences, are switched very
quickly one by one. In quick succession, it
looks as if those pictures are moving to the
human eye.
This Anime projector shows just ten pictures.
However, the image would be
more smooth (just like a TV show), if it
projected thirty pictures per second
Light is applied to the front and a reflection
of the image is then magnified by a lens to
project an image. This is called a reflective
type of projector. These days, movies mainly
use color films, whereas in the golden age of
black-and-white movies they very expensive
to produce and the images needed
developing. That is why it is said that paper
films and the reflection type of colored movie
gained popularity.
7. Preparation prior to experiments
7. Preparation prior to experiments
Place batteries as shown. Place batteries
with the +/- terminals in the correct position.
8. How to play
8. How to play
Turn the LED light on and project it onto the
wall in a dark room.
When the image is in focus, slowly turn the
handle.
Move the light source box back and forth to
a distance of 60 to 70 cm away from the wall
to find the spot where the projected image
is clear and in focus. For smaller image
P10
projection, keep a shorter distance between
the wall and the projector.
9. Create your own animation!
9. Create your own animation!
Cut a sheet of paper into 40 x 40 mm
squares and draw pictures on them.
Stick the drawings onto the drum from the
back side of the main body.
10. Troubleshooting
10. Troubleshooting
Miniature bulb DOES NOT light up or is dark.
- Read the instructions again and check
the wiring carefully.
- Read the instructions again and check
the orientation of both batteries.
- Replace batteries with new ones.
When the projected image is blurred or
invisible.
- Read "How to play" again and try focusing
better.
- Use a room that is as dark as possible.
- Project images on a flat and smooth wall.
(FR)
INSTRUCTIONS POUR LES ENFANTS DE
8 ANS ET PLUS :
Avant de commencer :
Avant de commencer :
- Vérifier le contenu de la boîte.
- Bien lire les instructions avant de monter.
- Manipuler les pièces en carton avec soin
pour qu'elles ne se déchirent pas.
- Manipuler l'objectif avec soin pour éviter
qu'il ne se raie ou qu'il ne se tache.
Tu auras besoin de :
Tu auras besoin de :
- Ruban adhésif
- Ciseaux
- 2 Piles AA
1. Description des pièces :
1. Description des pièces :
1.1. Base gauche
1.2. Base droite
1.3. Partie A de la boîte de lumière
1.4. Partie B de la boîte de lumière
1.5. Base avant
1.6. Fixation du porte-ampoules
1.7. Pièce du tambour
1.8. 2 Petits Disques
1.9. 2 Supports de l'objectif
1.10. Porte-objectif
1.11. 2 Grands Disques
1.12. objectif
1.13. Images
1.14. 2 Boîtiers de piles AA
1.15. Interrupteur
1.16. Ampoule LED
1.17. Porte-ampoules
1.18. 6 Fiches de branchement
1.19. Ruban adhésif épais
1.20. Ruban adhésif mince
1.21. Colle
1.22. Câble
1.23-24-25. Pièces manivelle
2. Montage de la lampe
2. Montage de la lampe
2.1. Insérer le porte-ampoules (17) dans
l'orifice du papier (6).
2.2. Fixer avec du ruban adhésif à l'arrière
pour éviter qu'il ne bouge.
2.3. Plier en suivant les lignes, monter et
attacher les rabats
Publicidad
