Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
OBJ_DOKU-54076-001.fm Page 11 Tuesday, July 12, 2016 4:06 PM
Changing the Button Cell (see figure B)
The cordless worklight is equipped with a CR2032 button cell
so that it can be detected by the mobile terminal device even
if no battery pack 12 is inserted.
To change the button cell, unlock the lock of the battery pack
cover 2 and fold up the battery pack cover 3. Unscrew the
screw of the battery lid 9 and take off the battery lid 10. Re-
move the empty button cell and insert a new button cell.
Make sure that the battery holder is not damaged when
removing the battery. Make sure that the plus pole of the
button cell faces upwards.
Remove the separating film between the button cell 11 and
the battery holder when using the tool for the first time.
Close the battery pack cover 3 and then the lock of the battery
pack cover 2.
Make sure that the rubber lip is seated correctly when
closing the battery pack cover. Otherwise protection
against dust and splash water will not be ensured.
A warning will be displayed in the app before the button cell is
fully used up.
Standing Up
Carefully fold out the pedestal and place the cordless work-
light on the floor. Ensure that it has a firm footing.
Fastening to the tripod
You can use the tripod mount 7 to screw the cordless work-
light onto a tripod.
Tighten the 5/8" screw. Ensure that the tripod has a firm
footing.
Swivelling the Lamp Head (see figure A)
The lamp head is attached to the handle. The lamp head can
be set to five positions using the handle.
Switching On and Off
To start the cordless worklight, press the On/Off switch 1.
To switch off the cordless worklight, press the On/Off switch
1 again.
To save energy, only switch the cordless worklight on when
using it.
Adjusting the Brightness
Press the On/Off switch 1 briefly to switch on the cordless
worklight at maximum brightness. To adjust the brightness in
2 stages, hold down the On/Off switch 1 until the required
brightness is obtained.
Temperature Dependent Overload Protection
When exceeding the allowable heat-sink temperature of
60 °C, the cordless worklight switches off. Allow the cordless
worklight to cool down, then switch the cordless worklight on
again.
Control via App
The cordless worklight is equipped with a Bluetooth® module
which enables wireless data transfer to certain mobile termi-
nal devices which have a Bluetooth® interface (e.g. smart-
phone, tablet).
Bosch Power Tools
In order to control the cordless worklight via Bluetooth®, you
will need the "Bosch Toolbox" app. Download the app from
the corresponding app store (Apple App Store, Google Play
Store).
Then select the "Floodlight" subitem in the app. The display of
your mobile terminal device will show you all subsequent
steps required to connect the cordless worklight to the termi-
nal device.
The following information will be available when a connection
has been established with the mobile terminal device: remote
control, time control, combining multiple cordless worklights
in one group.
Working Advice
Shortly before the cordless worklight switches off because of
an empty battery, it will flash 3 times and shine with reduced
brightness.
Troubleshooting – Causes and Corrective Measures
Cause
Corrective Measure
A Bluetooth connection cannot be established with the
cordless worklight.
The cordless worklight is not
Remove the button cell 11
emitting a Bluetooth signal.
and battery pack 12 for 10
seconds.
The cordless worklight cannot be switched on after wire-
less charging.
The inductively chargeable
Remove the battery pack 12
battery pack has to be
for 10 seconds.
re-initialised.
Maintenance and Service
Maintenance and Cleaning
The light source cannot be replaced. If the light source is de-
fective, the entire cordless worklight has to be replaced.
When the battery is no longer operative, please refer to an au-
thorised after-sales service agent for Bosch power tools.
The cordless worklight is maintenance-free and contains no
components that must be replaced or maintained.
To avoid damage, clean the plastic lens of the cordless work-
light only with a dry, soft cloth. Do not use cleaning agents or
solvent.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the nameplate of
the product.
English | 11
1 609 92A 2SA | (12.7.16)
Publicidad
Tabla de contenido
