Safety And General Information; Product Description - Omega Lift Equipment 41100C Manual De Instrucciones

SAFETY and GENERAL INFORMATION

Save these instructions. For your safety, read, understand, and follow the information provided with and on this jack
before using. The owner and operator of this equipment shall have an understanding of this jack and safe operating
procedures before attempting to use. The owner and operator shall be aware that use and repair of this product
may require special skills and knowledge. Instructions and safety information shall be conveyed in the operator's
native language before use of this jack is authorized. If any doubt exists as to the safe and proper use of this jack,
remove from service immediately.
Inspect before each use. Do not use if broken, bent, cracked or damaged parts are noted. Any jack that appears
damaged in any way, or operates abnormally shall be removed from service immediately. If the jack has been or
suspected to have been subjected to a shock load (a load dropped suddenly, unexpectedly upon it), immediately
discontinue use until jack has been checked by a factory authorized service center (contact distributor or manufacturer
for list of authorized service centers). It is recommended that an annual inspection be done by qualified personnel.
Labels and Operator's Manuals are available from manufacturer.

PRODUCT DESCRIPTION

Transmission Jack is designed to be used as an aid in the removal and installation of automotive and light truck
transmissions, transfer cases and transaxles. This jack is for use under portable lift equipment, where vehicle must
be supported by an identical pair of appropriately rated jack stands.
!
NEVER use for any purpose other than those uses outlined above!
SPECIFICATIONS
Model Capacity Min. Height Max. Height
41100C 1,100 Lbs 9" 24-3/4"
42000C 1 Ton 7-7/8" 33-1/2"
Tilt Adjustment Knob
Lift Arm
*Oil Filler Plug (not shown)
(*) refer to replacement parts
illustration for location
Handle Sleeve
Handle
Release Valve Knob
Figure 1- Typical Transmission Jack Components (42000C shown)
Jack Size
28-3/4" x 15"
39-3/8" x 19-1/8"
Saddle Plate
Chain
Caster
2
PREPARATION
Assembly
The angles and chains are pre-assembled on the angle bar.
Install the angle bar assembly onto the saddle plate.
model 41100C (see Fig 2):
Tools required: 16 mm wrench.
1. Remove the M10 nuts & lock washers (A) from the of angle
bar.
2. Place the angle bar to on slot of the saddle plate (B), adjust
to desired position then tighten the nut & lock washer (A).
3. Repeat for the other angle bar.
model 42000C (see Fig 3):
Tools required: 18 mm wrench.
1. Remove the M12x35 bolt, washers & nut (C & D) from the
angle bar.
2. Place and align the angle bar to one slot of the saddle plate.
3. Insert flat washer & bolt (C) through the angle bar hole and
saddle plate slot (E). Adjust to desired position then tighten
with nut and lock washer (D).
4. Repeat for the other angle bar.
Before Use
1. Verify that the product and application are compatible, if in doubt call Omega Technical Service (888) 332-6419.
2. Before using this product, read the operator's manual completely and familiarize yourself thoroughly with the
product, its components and recognize the hazards associated with its use.
3. To familiarize yourself with basic operation, locate and turn the release valve knob (see Fig 1):
a. Clockwise until firm resistance is felt to further turning. This is the 'CLOSED' release valve position used to
raise the saddle plate.
b. Counter-clockwise, but no more than 1/2 turn from the closed position. This is the 'OPEN' release valve position
used to lower the saddle plate.
4. With saddle fully lowered and release valve closed, pump the operating handle. If lift arm responds immediately,
jack is ready for use. If jack does not respond, follow the Bleeding/Venting instructions.
5. Ensure that jack rolls freely. Raise and lower the unloaded jack throughout the lifting range before putting into
service to ensure the pump operates smoothly. Replace worn or damaged parts and assemblies with factory
authorized replacement parts only.
Bleeding / Venting Trapped Air
With the release valve in the OPEN position (3b.) and with saddle fully lowered, locate and remove the oil filler
plug. Pump 6 to 8 full strokes. This will help release any pressurized air which may be trapped within the reservoir.
Reinstall the oil filler plug.
Fig. 2
Angle
Screw Hook Angle Bar
Saddle
Plate
(B)
(A)
Fig. 3
L-Hook
Angle
Shackle
(C)
Angle Bar
Saddle Plate
(E)
(D)
3