Chapin G2000P Manual De Instrucciones

WARNING
WARNING: Improper use or failure to follow instructions can result in explosive failure causing serious eye or
other injury. For safe use of this product you must read and follow all instructions. Do not leave a pressurized sprayer
in the hot sun. Heat can cause pressure build-up resulting in possible explosion. Do not store or leave solution in
tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full foot protection when spraying. Never
use any tool to remove pump if there is pressure in sprayer. Never stand with face or body over top of tank when
pumping or loosening pump to prevent ejecting pump assembly and/or solution from striking and injuring you. Never
pressurize sprayer by any means other than the original pump. Do not attempt to modify this sprayer. Replace parts
only with manufacturer's original parts. Never spray flammable, caustic, acidic, chlorine, bleach or other corrosive
solutions or heat, pressure, or gas producing chemicals. Always read and follow chemical manufacturer's
instructions before use with this sprayer as some chemicals may be hazardous when used with this sprayer.
WARNING: This product contains chemicals, including lead, known to the state of California
to cause birth defects and other reproductive harm. Wash hands after handling.
Congratulations!
You have just purchased a quality Chapin product. Register Your Sprayer Online @ www.chapinmfg.com
Questions? Do Not Return To Store. Call us @ 1-800-950-4458 or www.chapinmfg.com
¡Felicitaciones!
Usted acaba de adquirir un producto de calidad Chapin. Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas? No regrese a la tienda; llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin. Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:
www.chapinmfg.com Questions ? Ne retournez pas au magasin. Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
Parts, Piezas, Pièces
6-8096 6-8122 6-8093
Flat Fan Brass Adjustable Poly Adjustable
Nozzle Nozzle Nozzle
Tobera Tobera Tobera
Buse Buse Buse
6-8138 6-8148
Nozzle Kit
Shut-off Assembly
Tobera
Unidad de cierre
Buse
Assemblage d'arrêt
6-8101
Extension wand, Vara de extensión, Lance de rallonge
Elbow O-ring Hose Washer
6-8153
O-ring Kit
Nozzle Gasket Wand O-ring
6-5388
Hose Assembly
Ensamblaje de la manguera
Filter
Assemblage de boyau
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d'étanchéité (non inclus) 6-4601
1. Assembly of Shut-off, Extension Wand and Nozzle
1a
Shut-off Assembly
1) Screw nozzle assembly onto threaded end of the extension wand securely.
2) Insert unthreaded end of extension into shut-off assembly as shown and tighten retaining nut securely.
Nozzle Assembly
Figure 1-2
Sk-1154-1
Unscrew the nozzle cap (1) from the nozzle body (3) with retaining nut (2) fastened tightly to the elbow (5). Unscrew
the retaining nut (2). Push the nozzle body (3) with the nozzle gasket (4) out of the retaining nut (2). To reinstall the
nozzle, reverse the above instructions.
Figure 3
Unscrew the retaining nut from the elbow and push the fan nozzle tip and gasket out of the retaining nut. To reinstall the
nozzle, reverse the above instructions.
1. Poly
Nozzle Cap
2. Retaining
Nut
3. Nozzle
Body
4. Nozzle
Gasket
5. Elbow
2. Filter
The filter helps prevent clogging while spraying. It is located
on the end of the white tube inside your sprayer tank.To
clean filter, remove the hose from the tank and lift out the
outlet tube. Make sure the filter is positioned at the bottom
of the tank as pictured.
3. Pre-Use Check
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found, replace hose
before using. Replace with original manufacturer's parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank for
signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening and could
result in explosive bursting under pressure. If any of these signs are found, discard tank immediately and replace.
Do not attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20 strokes and
inspect for leaks).
5) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with
Filling, Pressurizing and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and fittings for rust, corrosion and pitting. If any of these
conditions are found, replace affected part with original manufacturer's part before using.
4. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.
013882-3 (A) R0116
Nozzle Assembly
Retaining Nut
Extension Wand
1. Brass
Nozzle Cap
2. Retaining
Retaining
Nut
Nut
3. Nozzle
Fan Nozzle
Body
Tip
Nozzle
4. Nozzle
Gasket
Gasket
Elbow
5. Elbow
2a
Filter
5. Pressurizing and Spraying
5A 5B
Do: Turn handle clockwise to Do: Pump until you
tighten. Push handle down, feel resistance.
turn 1/4 turn counterclock-
wise to release.
6. To Release Pressure
6A
1) Your sprayer is equipped with a pressure relief/release
valve (Fig. 6A). To release pressure lift and hold the cap
until air is completely exhausted, OR, turn the valve slowly
counterclockwise until you hear air escaping and wait air is
completely exhausted (Fig. 6B).
2) Do: Stay away from the sprayer until all air has escaped.
7. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling, Pressurizing and
Spraying Instructions, except pump unit only 8-10 strokes. Be sure that the wand and nozzle are thoroughly
rinsed with water after each use.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.
8. Fatigue-free spraying
LOCK-OFF POSITION LOCK-ON POSITION
Locking Mechanism Handle
8a 8c
8b
Down
Handle
Up
For safety lock-off feature (no-spraying), pull up on handle and move red locking mechanism into lock-off
position as shown in fig. 8a. To disengage, push down on handle and return red locking mechanismto
neutral position as in fig. 8c. For lock-on feature (continuous spraying), push down on handle and move red
locking mechanism into lock-on position as shown in fig. 8b. To disengage, push down on handle and return
red locking mechanism to neutral position as shown in fig. 8c.
9. Replacing Hose to Tank
9A 9B 9C
Black
No gap
Adapter
Make sure black adapter Press hose over adapter. Make sure worm gear
is attached to outlet tube clamp is below black
adapter. adapter .
5C
Do: Push handle, down, turn
1/4 turn clockwise to lock. Begin
spraying. Re-pump sprayer as
required to maintain spray force.
6B
NEUTRAL POSITION
9D
Tighten clamp fully.