Rules For Safe Driving; Assistance Service - Peg-Perego RACER Empleo Y Manutencion

RULES FOR SAFE DRIVING

For the safety of the child, before starting up the
vehicle read and carefully follow the following
instructions.
• Teach the child how to use the vehicle properly for
safe and enjoyable driving.
• The toy must be used with caution, as it requires
substantial dexterity in order to avoid falls or
collisions which could cause injuries to the user or
third parties.
• Before starting, check that there are no people or
objects obstructing the vehicle's path.
• Drive with hands on the handlebars/steering wheel
and always watch the road ahead.
• Brake in good time to avoid collisions.
ATTENTION! The item is equipped with a brake
system which needs to be appropriately illustrated to
the child by an adult.
2nd GEAR (if present)
Initially, use in 1st gear is recommended. Before
enabling 2nd gear, check that the child has learned to
use the handlebars/steering wheel, 1st gear and the
brake correctly, and has become familiar with the
vehicle.
WARNING!
• Check that all the wheel fixing studs/nuts are
fastened properly.
• If the vehicle is overloaded, as can happen on soft
sand, mud, or very uneven ground, the overload
switch will immediately disconnect the power. The
power supply will be restored after a few seconds..
• Only for 12 and 24 Volt vehicles: in first gear the
vehicle has a differential effect like a real motor
vehicle; on smooth terrain and with just one child
on board, the two wheels can turn at different
speeds and they can slip and slow down.
UNINTERRUPTED FUN: Keep a spare set of charged
batteries ready for use.
PROBLEMS?
THE VEHICLE DOES NOT WORK?
• Check that there are no disconnected cables under
the accelerator plate.
• Check the operation of the accelerator button and
replace it if necessary.
• Check that the battery is connected to the
electrical system.
THE VEHICLE LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by
an assistance centre.

ASSISTANCE SERVICE

offers an after-sales assistance service,
PEG PEREGO
directly or through a network of authorized
assistance centres, for any repairs or replacements
and the sale of original spare parts. To contact the
assistance centres refer to the "Assistance Centres"
booklet included in the packaging.
The item's serial number must always be quoted.
See the page on spare parts to find out how to
identify the serial number.
Peg Perego always strive to best satisfy their
customers' needs. Knowing the opinions of our
customers is therefore very important and valuable
to us. We would be very grateful if, once you have
used the product, you would fill out the
which you can find on
SATISFACTION QUESTIONNAIRE
the internet at: www.pegperego.com, making
any observations or suggestions you might have.
ASSEMBLY INSTRUCTIONS
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE
VEHICLE FROM ITS PACKAGING. ALL THE
SCREWS AND SMALL PARTS ARE CONTAINED IN
A BAG INSIDE THE PACKAGING. THE BATTERY
MAY ALREADY BE FITTED INSIDE THE ITEM.
1 • Insert the steering shaft from below the vehicle,
positioning the bend in the tube as shown in the
figure.
2 • Turn the vehicle upside down. In the front
section, position the steering rod as shown in the
figure.
3 • Slightly raise the two steering levers, rotating
them until they engage with the ends of the
steering rod.
4 • Attach the two steering levers to the steering
rod with the screws and washers provided.
5 • Press to snap fit the hub caps onto the four
wheels.
6 • Insert the small bushes into the housing on the
inside of two of the four wheels, as shown in the
figure.
7 • Slide a washer and a wheel onto each of the two
steering levers.
8 • Insert a self-locking washer into the special tool,
as shown in the figure. Important: the wings of
the self locking washer must be facing the inside
of the tool (see detail A).
NOTE: spare self locking washers are included in
the bag. These should be kept in case one breaks
and needs replacing.
9 • Holding the vehicle still, fix the wheel as shown
in the figure. Repeat for the other front wheel.
10 • Insert a self-locking washer into the special tool,
as shown in the figure. Important: the wings of
the self locking washer must be facing the inside
of the tool (see detail A).
11 • Remove the grey protector caps from the ends
of the rear axle. Insert the axle into the tool as
shown in the figure.
12 • Fully insert the large pentagonal-shaped bush
inside one of the two remaining wheels.
13 • Insert the axle into the wheel as shown in the
figure.
14 • Insert the whole unit into the rear of the vehicle
(gear motor side), engaging the gear motor
pentagon into the bush as shown in the figure.
15 • Fully insert the large rounded bush inside the
remaining wheel.
16 • Insert a washer and the remaining wheel onto
the other end of the axle.
17 • Position the conical tool, which was used
previously, on the axle (gear motor side). Taking
care that the tool does not move, turn the
vehicle onto the gear motor side. Insert a self
locking washer into the remaining tool provided
and attach the wheel (see figure).
18 • Turn the vehicle back onto its wheels and fit the
four boss cover caps, making sure the teeth
engage into the respective cavities.
19 • Fit the front plate, applying pressure to snap it
into its slots in the bodywork.
20 • Apply transfers A and B to the front plate.
21 • Press the front lights to snap them into place.
22 • Insert the windscreen into its three slots.
23 • Fasten the windscreen at the sides with the two
screws.
24 • Follow the instructions included in the packaging
of the horn to fit it on the steering wheel.
25 • Insert the steering wheel onto the steering shaft,
aligning the holes in the two elements.
26 • Fasten the steering wheel with the screw and nut
provided. IMPORTANT: the nut must be inserted
into the hexagonal hole and the screw into the
round hole.
27 • Connect the plug of the electrical system to the
battery plug.
28 • Position the seat support, engaging first the two
rear tabs (1) and then the two front tabs (2).
29 • Put the seat in the required position by inserting
the two front tabs and then engaging the rear tab
(detail A). Important: the seat can be set in three
different positions according to the height of the
child.
30 • Fasten the seat with the screw.
31 • Insert the roll-bar into its slots.
32 • Fasten the roll-bar with the four screws
provided.
CONSUMER
FEATURES AND USE OF THE VEHICLE
33 • Accelerator and electric brake pedal. To brake, lift
your foot off the accelerator pedal and the brake
ASSEMBLY
will automatically be applied.
34 • With the gear selection button, it is also
possible to put the vehicle into reverse.
35 • HORN: There is a horn on the steering wheel
(A).
36 • The seat can be set in three different positions
depending on the height of the child.
REPLACING THE BATTERY
37 • Remove the screw behind the seat. Push the
seat locking tab to release it and allow access to
the battery compartment.
38 • Unscrew the battery holder and remove it.
39 • Disconnect the plugs by pressing them on the
sides.
• Remove and replace the battery. Reconnect the
plugs and screw the battery holder back on.
Close the seat and replace the retention screw.
CHARGING THE BATTERY
WARNING: BATTERY CHARGING AND EVERY
OTHER OPERATION ON THE ELECTRICAL
SYSTEM MUST BE CARRIED OUT BY ADULTS
ONLY.
THE BATTERY CAN ALSO BE CHARGED
WITHOUT REMOVING IT FROM THE TOY.
• Disconnect plug A of the electrical system from
the battery plug B by pressing the sides.
40 • Connect the battery charger plug into a
domestic power supply as per the attached
instructions. Connect plug B with plug C of the
battery charger.
• When charging is complete, detach the battery
charger from the domestic supply and then
disconnect plug C from plug B.
41 • Fully insert plug B into plug A until it engages
with a click. On completion always remember to
refit the battery holder (if the battery has been
removed), close the battery compartment, and
refit the seat with the retention screw.