SSS Siedle A 180-10 Informacion De Producto página 8

Scope of supply A 180-11
(Wall version with receiver)
• Siedle Axiom
• DECT™ receiver
• Wall mounting plate
• RJ45 socket
• A BLT 251-0 bus licence telephony
• This product information
Scope of supply A 180-20
(Table­top version without receiver)
• Siedle Axiom
• Tray with connector
• 8-pole connecting cables, 3 m long
with RJ45 plug
• A BLT 251-0 bus licence telephony
• This product information
Scope of supply A 180-21
(Table­top version with receiver)
• Siedle Axiom
• DECT™ receiver
• Tray with connector
• 8-pole connecting cables, 3 m long
with RJ45 plug
• A BLT 251-0 bus licence telephony
• This product information
Scope of supply A 180-30
(Furniture version without receiver)
• Siedle Axiom
• Furniture adapter
• 8-pole connecting cables, 3 m long
with RJ45 plug
• A BLT 251-0 bus licence telephony
• This product information
Scope of supply A 180-31
(Furniture version with receiver)
• Siedle Axiom
• DECT™ receiver
• Furniture adapter
• 8-pole connecting cables, 3 m long
with RJ45 plug
• A BLT 251-0 bus licence telephony
• This product information
Terminal assignment
RJ45 LAN
8
Mounting
Wall version
1 Recommended mounting height
appr. 1.60 m to display height/
viewing height.
The centre of the display sits 21 mm
above the centre of the double-
device junction box: so with a height
of 1600 mm, the centre of the box
must be set to 1579 mm.
2 Wire up the provided RJ45 socket
according to the instructions and
snap into the wall mounting plate
from behind.
3 When mounting directly on the
wall, fasten the base plate using
4 screws, paying attention that
the plate is the right way up (top
marking). Double device junction
box with an installation depth of at
least 47 mm required.
4 When mounting on a switch box,
use the screw openings in the centre
of the device, paying attention that
the plate is the right way up (top
marking).
Double device junction box with an
installation depth of at least 47 mm
required.
5 Snap the panel onto the wall
mounting plate.
6 Place the DECT™ receiver on the
magnetic holder.
Table-top version
7 Insert the connecting cable into
the panel from below.
8 Terminal assignment RJ45 socket
9 Snap the panel onto the magnetic
connector.
10 Place the DECT™ receiver on the
magnetic holder.
Furniture version
11 In the desired location for the
Axiom, drill a hole with a max. diam-
eter of 15 mm through the furniture
plate. Position the furniture adapter
over the hole and secure it with suit-
able screws. Insert the connecting
cable through the hole into the
panel from below.
Snap the panel onto the magnetic
furniture adapter.
Place the DECT™ receiver on the
magnetic holder.
Installation and commissioning
The commissioning instructions
for the Smart Gateway, the system
manuals for the In­Home bus and
the operating instructions for the
Siedle Axiom can be found in the
download area.
Video memory
Images are stored centrally on the
Smart Gateway.
Similar to photographs, saved
images are subject to copyright.
Bus licence BLT 251-0
Application licence for enabling an
external connecting channel for VoIP
telephony with Siedle Axiom and
the Smart Gateway. One application
licence BLT 251-0 can be imported
per Smart Gateway. One free user
licence is additionally required for
the integration of a VoIP telephone
system.
The following conditions apply to
the use of an application licence
BLT 250-0:
• Ready­to­use Smart Gateway with
firmware from V 1.3.0
• Siedle Axiom
• Pre-configured, ready-to-use VoIP
telephony connection (SIP client/
SIP trunk)
• Free user licence (BLC 250-0 bus
licence client) for one IP user
The licence is linked to the hard­
ware. If a Smart Gateway fails, Siedle
transfers all licences purchased
within the last 2 years free of charge
to an identical substitute device
(investment protection).
Cable type
A 3 m patch cable is included
with the device as standard. The
same cable type is also available in
other lengths at www.lindy.com if
required.
In any case, a flat cable with the
same specification as the original
cable must be used.