Evolution R210 SMS Instrucciones Originales página 22

INSERTING THE CARRIAGE SLIDE
IMPORTANT: If for any reason (transit damage,
unpacking error, operator mistake, etc.) the
locating lugs at the tip of the carriage slide
arms have been 'tripped' , the sliding carriage
cannot be fitted into the bevel neck or onto
the cutting head. The locating lugs (Fig.11)
must be reset, if either or both have been
'tripped' prematurely.
RESETTING THE LOCATING LUGS
• Gently push the protruding lug into the
Carriage arm.
• Gently ease the locating lug deployment
plunger forward by using a flat bladed
screwdriver (not supplied) as a lever. (Fig. 12)
The carriage slides two (2) arms should be
inserted through the two linear bearings
contained within the bevel neck.
The carriage slide should be inserted from the
back ensuring that the 'Evolution' logo is the
correct way up. (Fig. 9)
• Slide the sliding carriage arms through
the bevel neck for approximately half of
their length.
• Screw the carriage slide locking screw into
the threaded hole above the right hand arm
of the carriage slide. (Fig. 10)
Note: Ensure that the anti-vibration spring is
fitted underneath the hand knob before fitting
the locking screw into its service position.
• Tighten the locking screw to lock the sliding
carriage into the desired position.
ATTACHING THE CUTTING HEAD
• Align the cutting head with the two (2)
sliding carriage arms. (Fig. 13a)
• Push the cutting head onto the Carriage
arms firmly until the 'click' of the Locating
Lugs deploying is heard. (Fig. 13b)
Note: The deployed locating lugs must be
fully visible when viewed from the side of the
cutting head. (Figs. 14a, 14b, 14c)
The Locating Lugs are coloured green to make
identification easy.
(R210SMS-300 & R210SMS-300+ Models)
Two additional screws are supplied which
should be screwed into the head of the saw
where it meets the rear sliding carriage rails.
This secures the rails in place reducing any
wobble that may occur. (Fig. 14d) The two
www.evolutionpowertools.com
screws are supplied with the rear cable guide
clamp in the packaging. These 2 screws can
be fitted with the supplied M5 hex key.
FITTING THE SLIDE RAIL COVER:
Note: Make sure the cutting head is in the
down right position before proceeding.
• Remove Slide Locking Screw and spring.
• With the saw's Cutting Head facing towards
you, align the Slide Rail Cover's cut out channel
over the right rail.
• Insert the single tab into the recess between
the two rails on the rear of the Cutting Head.
• Lower the Slide Rail Cover onto the rails
and click the two rear tabs into place on
the rear Carry Handle.
• Re-fit the Slide Locking Screw and
spring. (Fig. 15)
THE MACHINE TABLE EXTENSIONS (Fig. 16)
Note: Two (2) machine table extension pieces
are provided with this machine. They are
'handed' , one being for the right hand side,
and one for the left hand side.
TO FIT THE TABLE EXTENSIONS:
• Carefully examine the table extension pieces to
determine which is for the right hand side and
which is for the left hand side.
• Remove the socket headed screws (Fig. 17)
from the table using the hex key provided.
• Position the relevant Extension piece onto
the table and secure it into its service
position using the socket headed screws.
• Repeat for the second Extension piece.
ROUTING THE POWER CABLE
WARNING: This machine is equipped with a
mains cable and a moulded plug which satisfies
the regulations of the receiving country. This
cable and plug, if damaged, should only be
replaced with genuine Evolution replacement
parts and be fitted by a competent technician.
• Ensure that the cutting head is in the
down position.
• Ensure that the carriage slide is in its most
forward position and locked. (Fig. 18)
From the motor the mains cable should bypass
the front cable guide and then be routed
rearwards (Fig. 19).
The cable should be inserted into the rear
cable guide/clamp. Ensure the Cable Grip
Component is inside the cable guide when the
cable passes through.
This guide/clamp should then be fastened
22