Descargar Imprimir esta página

Steelcase Migration Manual Del Usuario página 3

Mesas de altura ajustable
Ocultar thumbs Ver también para Migration:

Publicidad

®
WARNING
RISK OF SERIOUS INJURY:
POTENTIAL FOR INJURY: The use of worksurfaces that do not comply with the Steelcase defined criteria and limitations could cause personal injury or property damage due to pinch
points, instability, or other problems.
POTENTIAL FOR NON-COMPLIANCE: The use of work surfaces that do not comply with Steelcase criteria VOIDS any Steelcase claims of compliance with ANSI/BIFMA, UL, LEED,
or other applicable requirements. The use of non-Steelcase work surfaces on Steelcase adjustable-height bases may NOT be accepted as compliant to municipal electrical codes or
OSHA federal workplace standards, because this use may not create an NRTL (UL, ETL, etc.) listed product. Steelcase is not responsible for the ultimate determinations of compliance
for height-adjustable bases with non-Steelcase work surfaces. Steelcase assumes NO liability for lack of standards compliance in these instances.
WARRANTY RESTRICTIONS: The use of non-Steelcase supplied work surfaces VOIDS all Steelcase warranties, expressed or implied.
DISCLAIMER: The use of non-Steelcase work surfaces is NOT recommended. Any use of a non-Steelcase work surface requires additional investigation by the customer regarding the
appropriateness for use. It is the sole responsibility of the customer to determine the suitability and safety of the selected work surface construction and attachment means. The following
information is provided as a guideline, but does not address all potential issues. Customers should seek professional guidance as to the appropriateness of their chosen work surface.
MANDATORY REQUIREMENTS REGARDLESS OF WORK SURFACE MATERIAL OR CONSTRUCTION:
FASTENERS: Adjustable-height bases include fasteners intended for use with Steelcase work surfaces.
These fasteners may potentially also be suitable for work surfaces meeting the following criteria:
Medium-density or higher particleboard or fiberboard cores with High-pressure laminate (HPL), Low-
pressure laminate (LPL) or veneer & backers
Thickness of .984" (25.0 mm) or greater
Fasteners located a minimum distance of .984" (25.0 mm) from any edge
Any other work surface construction will require different and/or additional fastening means and these means
must be determined by the project's designer, architect, or engineer. For example, solid-surface materials
should use appropriate threaded inserts and corresponding fasteners or similar attachment means.
In all cases, all fastener locations provided in the base attachment features MUST be used (e.g. if attachment
cantilever has 6 screw holes, all 6 holes must be used for attachment).
FLAMMABILITY: Any worksurface or similar large part > 10ft ^ 2 must have a flame spread <200 and
a smoke devloped index < 450 when tested per UL 723.
SHARP EDGES: All accessible edges of the work surface must meet 1439 test for sharp edges.
DIMENSIONAL LIMITATIONS:
Work surface depth not to exceed 36.0" (914.4 mm)
Longitudinal work surface position on base must be on centerline ± 2.0" (50.8 mm)
Work surface overhang (distance from side of support cantilever to edge of work surface) must be
greater than .984" (25.0mm) and may not exceed 15.0" (381 mm)
Work surface overhangs larger than .984" (25.0mm) are not allowed on widths < 64.0" (1625.6 mm)
Work surface overhangs between .984" (25.0mm) and 15.0" (381 mm) may exist on one side only for
tops that are ≥ 64.0" (1625.6 mm) and ≤ 71.645" (1820.8 mm)
Work surfaces larger than 71.685" (1820.8 mm) must have overhangs larger than .984" (25.0mm) on
at least one side, but may not exceed 15.0" (381 mm) on any side
Maximum work surface width may not exceed 101.685" (2582.8 mm)
FOLLOW ALL WARNINGS PROVIDED FOR BASE + WORK SURFACE.
WORKSURFACE
WIDTH
+
C L
NOTE: DESK IMAGE IS FOR
REFERENCE ONLY. TABLE
SHAPE AND LEG QUANTITY MAY
CHANGE BASED ON STYLE AND
CONFIGURATION
WORKSURFACE
OVERHANG
BASE-ONLY
WORKSURFACE
DEPTH
Page 3 of 41
Doc # 68446

Publicidad

loading