Publicidad
Idiomas disponibles
Idiomas disponibles
Always wear SAFETY GLASSES
when installing hitch
Scan for step by step
PHOTO installation
instruction or visit
http://www.cequentgro
up.com/qr-product.aspx
Note: Fasteners typical
both sides
Teeth side
against hitch
Figure 2
Using pliers bend bumper hanger
support to approximately 90 degree
for clearance.
1.
Remove plastic rivet – Remove the (2) plastic rivets that fasten the fascia tabs to the vehicle and trunk pan. Note: Remove the center of the rivet with a flat screwdriver. Keep for re-installation.
2.
Open trunk remove tail lights and gasket – remove the plastic cover disc coving the screw on the tail light and fascia attachment to trunk with small screwdriver (3) each side. Remove the fasteners with
10mm socket. Remove lower trunk gasket. To remove tail light gently push rearward on tail lights at the back of the light while gently pulling outward from the forward end. Disconnect the wiring. Set
aside.
3.
Remove lower rear fascia – remove (2) philip screws in wheel well. Both sides. Remove (1) philip screw each side, located inside fascia at the lower attaching points between rear fascia and rear side
panel of vehicle. Both sides. Gently separate the lower fascia trim from the rear side panel pulling the trim upward (if necessary apply minimum pressure to tabs located on the inside of the rear fascia.
At the tail lights apply gentle pressure to support bracket tabs. Continue to gently pull on fascia while lifting upward from the bottom of the fascia. Carefully set the rear fascia aside.
4.
Remove bumper - remove bumper using 12mm socket (6) bolts. Carefully set the bumper aside. Using pliers bend bumper hanger support to approximately 90 degree for clearance. See Figure 2
5.
Hitch installation – Hang the U-bolt on the tow hook. Raise the hitch and hang it on the bumper support on the end panel. Raise the bumper to sandwich the hitch, align the holes and reinstall the
original bolts removed in step 4. Tighten to hold hitch in place. Install remaining fastener for the tow hook.
6.
Tighten all M8 fasteners with torque wrench to 20 Lb.-Ft. (27 N*M) and all 3/8 GR 5 fasteners with torque wrench to 30 Lb.-Ft. (41 N*M)
7.
Trim fascia- locate the center of bottom panel (tow hook) and trim 3-3/4" x 3-3/4'' wide area, see Figure 3. Recommend radius in corners.
8.
Re-install fascia - Reinstall all fasteners , fascia and taillights removed in Step 1 - 3.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A hitch or
ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
©2016 Cequent™ Performance Products, Inc. -
Installation Instructions
PART NUMBERS: 24942, 77329,
End panel
Rear
Figure 1
Proper torque is needed to keep the hitch secure to the vehicle when towing.
Printed in Mexico
CQT24942
(Sold Separately )
Drawbar Kit:
3593
Drawbar must be used in the
RISE position only.
①
Tow
Hook
②
③
Re-use
existing
bolts
Sheet 3 of 15
Fastener Kit : 24942F
①
Qty. (1)
U-BOLT 3/8-16
GR5
②
Qty. (2)
Conical washer
3/8''
③
Qty. (2)
Hex nut
3/8-16
Existing
Weldnut
3-3/4"
[95.25]
Centerline
Figure 3
Fascia
trimming
24942NP
4-4-16
3-3/4"
[95.25]
1-7/8"
[47.625]
Tow
Hook
Rev. X
Publicidad
