Steering Wheel Audio Control Extra Settings; L.e.d. Feedback; Changing Radio Type - Axxess BX-MZ1 Instrucciones De Instalación

Steering wheel audio control extra settings

L.E.D. feedback

The (16) Red L.E.D. flashes represent what brand radio the BX-MZ1 believes it is
connected to. Each flash represents a different radio manufacturer. For example, if you
are installing a JVC radio, the BX-MZ1 will flash Red (5) times, and then stop. Following
is a legend that dictates which radio manufacturer corresponds to which flash .
L.E.D. feedback legend
1st L.E.D. flash is for Eclipse (Type 1) †
2nd L.E.D. flash is for Kenwood ‡
3rd L.E.D. flash is for Clarion (Type 1) †
4th L.E.D. flash is for Sony and Dual
5th L.E.D. flash is for JVC
6th L.E.D. flash is for Pioneer and Jensen
7th L.E.D. flash is for Alpine *
8th L.E.D. flash is for Visteon
* Note: If the BX-MZ1 flashes Red (7) times, and you do not have an Alpine radio connected to
it, that means the BX-MZ1 does not detect a radio connected it. Verify that the 3.5mm jack is
connected to the correct steering wheel jack/wire in the radio.
** Note: Part number AX-SWC-PARROT is required (sold separately). Also, the Parrot radio must
be updated to rev. 2.1.4 or higher through www.parrot.com.
† Note: If you have a Clarion radio and the steering wheel controls do not work, change the radio
type to the other Clarion radio type; same for Eclipse. The following section explains how to do this.
‡ Note: If you have a Kenwood radio and the L.E.D. feedback comes back as showing as a JVC
radio, change the radio type to a Kenwood. The following section explains how to do this.
9th L.E.D. flash is for Valor
10th L.E.D. flash is for Clarion (Type 2) †
11th L.E.D. flash is for Metra OE
12th L.E.D. flash is for Eclipse (Type 2) †
13th L.E.D. flash is for LG
14th L.E.D. flash is for Parrot **
15th L.E.D. flash is for XITE
16th L.E.D. flash is for Philips
BX-MZ1
Attention:
The Axxess Updater App can also be used to program the following (3)
sub-sections as well, pending that the interface has been initialized and programmed.

Changing radio type

If the LED flashes do not match the radio you have connected, you must
manually program the BX-MZ1 to tell it what radio it is connected to.
1) After (3) seconds of turning the key on, press and hold the Volume-Down button
on the steering wheel until the L.E.D. on the BX-MZ1 goes solid.
2) Release the Volume-Down button; the L.E.D. will go out indicating we are now
in Changing Radio Type mode.
3) Refer to the Radio Legend (next page) to know which radio number you would
like to have programmed.
4) Press and hold the Volume-Up button until the L.E.D. goes solid, and then
release. Repeat this step for the desired radio number you have selected.
5) Once the desired radio number has been selected, press and hold the Volume-
Down button on the steering wheel until the L.E.D. goes solid. The L.E.D. will
remain on for about (3) seconds while it stores the new radio information.
6) Once the L.E.D. goes off, the Changing Radio Type mode will then end. You can
now test the steering control wheel controls.
Note: If at any time the user fails to press any button for a period longer than
(10) seconds, this process will abort.
5
Continued on the next page