Sears Kenmore 796.4128 31 Serie Manual De Uso página 31

Lavadora automatica de carga frontal
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

BEFORE CALLING
FOR SERVICE (continued)
Your washing machine is
early stage.
Water in the washer
drains slowly
or not
at all, or the dlsplay
SHOWS:
I
_Tn-
uc|
Washer fills with
water slowly
or not
at all, or the dlsplay
equipped
with an automatic
error-monitoring
system to detect and diagnose
problems at an
Drain hose is kinked, pinched, or clogged.
The drain pump filter is clogged.
Drain discharge is more than 96 inches above
bottom of washer.
Water supply faucets are not open fully.
Water line hoses are kinked, pinched, or
crushed.
iiii_!_i_i_i
_C_!!!!_!_!!!_i_i_iiiiiiiiiiiiiiiii_i!_iiii_iiiiiiiiiiii!_iiii!!_iiiiiiiii!_iii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii!_i!_iiiii_i!_i_i_i!i!i!i
_ _;_II_I!'I
_i_i_i_i_i_iiiii!!!_iiiiii_i_iiii!_!_!i_i_ii_iiii_!i!;_!!i:!_i!_i!i
_:!i!i_iiii_ii_!i_ii!!!i!ii!ii!ii!ii!ii!ii!ii!ii!_i!i_!ii!_i!ii_i_i_i_i_i_
i _i_i_ii_!!_!_!_iiiiii/ii_iiii_i_ii!_ii_ii_i!i_iiiiiiii_i_i!_i_ii_ii_i!i_!i_i_i_i_i_i_i_
i!s!Oi_U_ii!ON_i_!_
_!_i!!!:!_!_i_i_i_i_i_i_i_i_i_i_iii_iii!
_i_i_i_i_ii!!_i_!_ii_iii
Make sure the drain hose is free of clogs, kinks, etc.,
and is not pinched behind or under the washer.
Clean the drain pump filter. See Maintenance in the
Care and Cleaning section.
Adjust or repair drain. Maximum drain height is 96
inches.
Make sure that the water faucets are fully open.
Make sure the hoses are not kinked or pinched.
Be careful when moving the washer during
shows:
cleaning and maintenance
I
/ E I
Water inlet filters are clogged.
Clean the inlet filters. See Maintenance
in the
Care and Cleaning
section.
Water supply pressure to faucet or house
Check another faucet in the house to make sure
is too low.
that household water pressure is adequate
and
flow is not restricted.
Water supply connected
with leak-limit-
Hoses designed to limit leaks can trip falsely and
ing hoses,
prevent the washer from filling. The use of leak
limiting hoses is not recommended.
Cycle won't start, or
The door is not closed properly.
Make sure that the door is closed properly
and
the display shows:
press the START/PAUSE button. After starting
If
,,- ,|
a cycle, it may take a few moments before the
|
QC
i_
drum begins to turn or spin. The washer will not
I
ih-__
operate unless the door is locked.
[]
If the door is closed and locked and the open
door error message is displayed,
call for service.
The display shows:
Load is too small.
Add 1 or 2 similar items
to help
balance the load.
il
UC''I-!
Load is out of balance.
The washer has an imbalance detection and
correction system. If individual heavy articles
are loaded (bath mat, bath robe, etc.) and the
imbalance is too greah the washer will make several
attempts to restart the spin cycle. If an imbalance
is still detected, the washer will stop and the error
_ code
will display.
The display shows:
'|
|
i
cc
The display shows:
|
'-'-
,-o-|
The display shows:
|
|
The display shows:
i
i|
Lc|
The display shows:
| PF|
Control error.
Water
level is too high due to a faulty
water
valve.
The water level sensor is not working
correctly.
A motor
error
has occurred.
A power failure
has occurred.
Unplug the washer and wait 60 seconds. Reconnect
power and try again. If the error reappears, caii for
service.
Close
the water
faucets,
unplug
the washeb
and coil
for service.
Close
the water
faucets,
unplug
the washeb
and call
for service.
Allow the washer to stand for 30 minutes and then
restart
the cycle.
If the LE error
code
persists,
call
for
service.
If the power to the washer has been interrupted
during a cycle, the PF error code will display
the next time the washer is turned ON. This will
alert you to the fact that the previous cycle may
not have been completed.
Select any cycle to
clear the error code and use the washer.
31

Publicidad

Tabla de contenido
loading

Tabla de contenido