Zoeller Home Guard Max 503 Manual Del Usuario página 2

Manufacturer warrants, to the purchaser and subsequent owner during the
warranty period, every new product to be free from defects in material and
workmanship under normal use and service, when properly used and maintained,
for a period of three years from date of manufacture. Parts that fail within
the warranty period, that inspections determine to be defective in material or
workmanship, will be repaired, replaced or remanufactured at Manufacturer's
option, provided however, that by so doing we will not be obligated to replace
an entire assembly, the entire mechanism or the complete unit. No allowance
will be made for shipping charges, damages, labor or other charges that may
occur due to product failure, repair or replacement.
This warranty does not apply to and there shall be no warranty for any material
or product that has been disassembled without prior approval of Manufacturer,
subjected to misuse, misapplication, neglect, alteration, accident or act of
nature; that has not been installed, operated or maintained in accordance with
Manufacturer's installation instructions; that has been exposed to outside
substances including but not limited to the following: sand, gravel, cement, mud,
tar, hydrocarbons, hydrocarbon derivatives (oil, gasoline, solvents, etc.), or other
abrasive or corrosive substances, wash towels or feminine sanitary products,
etc. in all pumping applications. The warranty set out in the paragraph above is
in lieu of all other warranties expressed or implied; and we do not authorize any
representative or other person to assume for us any other liability in connection
with our products.
In those instances where damages are incurred as a result of an alleged pump failure, the homeowner
1. The system is designed for installation in sumps with minimum diameter of
18" and depth of 22". For smaller applications, consult factory.
2. Remove all debris from the pit before installation.
3. Be sure that the pump is clamped securely to the primary pump discharge
pipe and that the two pumps do not interfere with each other.
4. Install a serviceable check valve in the discharge line.
1. DO read all installation materials supplied with the pump.
2. DO inspect unit for any visible damage caused by shipping. Contact dealer
if unit appears to be damaged.
3. DO clean all debris from the pit before installation.
4. DO install a union check valve (see STEP 3) in the discharge line. DO NOT
use a discharge pipe smaller than the recommended pump discharge
sizes.
5. DO install a filter or strainer in the water supply line before the pump to
prevent small particles from clogging the operating valve.
6. DO test the pump immediately after installation to be sure that the system is
working properly.
7. DO review all applicable local and national codes and verify that the
installation conforms to each of them.
LIMITED WARRANTY
must retain possession of the pump for investigation purposes.
Helpful Hints For Easy Installation
Do's And Don'ts For Installing A Unit
© Copyright 2020 Zoeller
2
Contact Manufacturer at, 3649 Cane Run Road, Louisville, Kentucky 40211,
Attention: Customer Support Department to obtain any needed repair or
replacement of part(s) or additional information pertaining to our warranty.
MANUFACTURER EXPRESSLY DISCLAIMS LIABILITY FOR SPECIAL, CONSEQUENTIAL
OR INCIDENTAL DAMAGES OR BREACH OF EXPRESSED OR IMPLIED WARRANTY;
AND ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND
OF MERCHANTABILITY SHALL BE LIMITED TO THE DURATION OF THE EXPRESSED
WARRANTY.
Some states do not allow limitations on the duration of an implied warranty, so
the above limitation may not apply to you. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
5. Install a filter or strainer in the water supply line before the pump. Size the
filter/strainer properly to minimize pressure drop, while retaining particles
0.020" (0.5 mm) in diameter and larger.
6. Test the unit immediately after installation. Refer to STEP 5.
7. Check the Float ON/OFF levels per STEP 2 of the instructions.
8. Keep the model number, date code, and installation instructions in a
convenient location for future reference.
8. DO NOT use the Home Guard
DO NOT use the Home Guard
effluent, or water with debris in it.
9. DO NOT use a garden hose. Garden hose is not designed to hold municipal
pressure indefinitely and could leak or burst causing flooding. The Home
Guard Max requires a permanent piping method such as copper, PEX, or
®
CPVC.
10. DO install the Home Guard
11. DO install a union or other quick-disconnect fitting to make the pump
accessible for servicing on both the water supply and discharge piping.
12. DO install a dedicated shut-off valve on the water supply line within 6 ft. (1.8
m) of the Home Guard Max.
®
Co. All rights reserved.
®
Max with hot water.
®
Max to remove wastewater, sewage,
®
Max pump with only a 3/4" supply line.
®