Sauder Harbor View Serie Manual Del Usuario
  1. Manuales
  2. Marcas
  3. Sauder Manuales
  4. Muebles de Interior
  5. Harbor View Serie
  6. Manual del usuario

Sauder Harbor View Serie Manual Del Usuario

Ocultar thumbs Ver también para Harbor View Serie:
Tabla de contenido

Publicidad

Enlaces rápidos

Descargar este manual
sauder.com
Storage Cabinet
Harbor View Collection | Model 423661
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
Store behind
closed doors.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-22
Français pg 23-25
Español pg 26-28
Lot # 519821
09/24/18
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987

Publicidad

Tabla de contenido
loading

Manuales relacionados para Sauder Harbor View Serie

Resumen de contenidos para Sauder Harbor View Serie

  • Página 1 Harbor View Collection | Model 423661 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Prefer the phone? Call 1-800-523-3987.
  • Página 2 Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 5-22 Hammer Not actual size Français 23-25 Español 26-28 Skip the power trip. Safety 29-30 This time. Warranty Page 2 423661 www.sauder.com/services...

  • Página 3: Part Identifi Cation

    VALANCE (1) RIGHT DOOR (1) FRONT MOLDING (1) UPPER SHELF (1) LEFT DOOR (1) RIGHT MOLDING (1) BOTTOM (1) SMALL BACK (1) LEFT MOLDING (1) SHELF (1) LARGE BACK (1) SMALL END (2) ADJUSTABLE SHELF (1) www.sauder.com/services 423661 Page 3...

  • Página 4: Tabla De Contenido

    BLACK 9/16" LARGE HEAD SCREW - 27 BLACK 1-1/8" PAN HEAD SCREW - 2 BLACK 1/2" FLAT HEAD SCREW - 8 SILVER 2" FLAT HEAD SCREW - 7 113S BLACK 1-15/16" FLAT HEAD SCREW - 4 Page 4 423661 www.sauder.com/services...
  • Página 5 Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. Some assembly To begin assembly, push sixteen SAUDER TWIST-LOCK® å (and snacks) required. FASTENERS (36F) into the large holes in the ENDS (A), SMALL ENDS (F), BOTTOM (K), and SHELF (L).
  • Página 6 Step 2 Tap two MOLDING CONNECTORS (18F) into the notches å in the MOLDINGS (C, D, and E). Use your hammer to tap the MOLDING CONNECTORS (18F) into the notches in the MOLDINGS. Flat end Flat end Page 6 423661 www.sauder.com/services...

  • Página 7: Black 9/16" Large Head Screw

    BLACK 9/16" LARGE HEAD SCREW (1S). NOTE: Position the SAFETY STRAP (60M) exactly as shown. å BLACK 9/16" LARGE HEAD SCREW (1 used for the SAFETY STRAP) Curved edge SILVER 2" FLAT HEAD SCREW (7 used for the MOLDINGS) www.sauder.com/services 423661 Page 7...

  • Página 8: Twist-Lock Fastener

    (8 used for the METAL BRACKETS) METAL BRACKETS on the SMALL ENDS and into the holes in the END MOLDINGS. Edge with TWIST-LOCK® FASTENERS These holes are closer to this edge. These surfaces should be even. Page 8 423661 www.sauder.com/services...
  • Página 9 Step 5 Fasten the SMALL ENDS (F) to the MOLDINGS (D and E). å How to use the SAUDER TWIST-LOCK® FASTENER Tighten four TWIST-LOCK® FASTENERS. 1. Insert the dowel end of the FASTENER into the hole of the adjoining part.
  • Página 10 END MOLDINGS (G). Use four BLACK 9/16" LARGE HEAD SCREWS (1S) through the TIE PLATES and into the BLACK 9/16" LARGE HEAD SCREW holes in the MOLDINGS. (8 used for the TIE PLATES) Curved edge Page 10 423661 www.sauder.com/services...

  • Página 11: Black 1-15/16" Flat Head Screw

    Fasten the UPPER SHELF (J) to the SMALL ENDS (F). Use å four BLACK 1-15/16" FLAT HEAD SCREWS (113S). NOTE: Start each SCREW a few turns before tightening å any of them. 113S BLACK 1-15/16" FLAT HEAD SCREW (4 used for the UPPER SHELF) Curved edge www.sauder.com/services 423661 Page 11...
  • Página 12 SHELF (J). Tighten two TWIST-LOCK® FASTENERS. Back edge i t h ® f a c S u r - L O I S T E R S T E N F A S For support, place packing foam and magazines here. Page 12 423661 www.sauder.com/services...
  • Página 13 S u r f a c i t h I S T - L O F A S T E N ® E R S These holes must be here. For support, place packing foam and magazines here. www.sauder.com/services 423661 Page 13...
  • Página 14 SHELF (J), BOTTOM (K), and SHELF (L). Tighten six TWIST-LOCK® FASTENERS. i t h o ® f a c S u r - L O I S T E R S T E N F A S Page 14 423661 www.sauder.com/services...
  • Página 15 Fasten the BASE (N) to the ENDS (A) and BOTTOM (K). Use fi ve å BLACK 9/16" LARGE HEAD SCREWS (1S) through the METAL BRACKETS on the ENDS and BOTTOM and into the BASE. BLACK 9/16" LARGE HEAD SCREW (10 used for the METAL BRACKETS) www.sauder.com/services 423661 Page 15...

  • Página 16: Safety Strap

    å line up over the SHELF (L). These holes must line up over the UPPER SHELF (J). These holes must line up over the SHELF (L). The LARGE BACK (R) will overlap the SMALL BACK (Q). Page 16 423661 www.sauder.com/services...
  • Página 17 Step 13 Fasten four HINGES (13H) to the DOORS (O and P). Use å eight BLACK 1/2" FLAT HEAD SCREWS (11S). BLACK 1/2" FLAT HEAD SCREW (8 used for the HINGES) www.sauder.com/services 423661 Page 17...

  • Página 18: Black 1-1/8" Pan Head Screw

    å BLACK 1-1/8" PAN HEAD SCREW (9S). Repeat this step for the RIGHT DOOR (O). å See the next step for DOOR adjustments. å 134K BLACK 1-1/8" PAN HEAD SCREW (2 used for the KNOBS) 160M Page 18 423661 www.sauder.com/services...
  • Página 19 To adjust the DOORS in or out (depth), loosen the mounting å screw one turn and move the DOORS in or out, as needed. Tighten the mounting screw after making adjustments. Mounting screw (depth) Adjusting screw (horizontal) (vertical adjustment) www.sauder.com/services 423661 Page 19...
  • Página 20 5. Continue to turn until the screw starts spinning freely. å NOTE: Before moving your unit to a diff erent location, unscrew the SAFETY DRYWALL ANCHOR (61M) from your wall. The nylon sheath will remain behind your wall. Page 20 423661 www.sauder.com/services...
  • Página 21 Push the RUBBER SLEEVES (2R) over the METAL PINS (1R). å Insert the METAL PINS into the hole locations of your choice Almost time to in the LARGE ENDS (A). Set the ADJUSTABLE SHELF (M) celebrate! With a nap. onto the METAL PINS. (4 used) www.sauder.com/services 423661 Page 21...
  • Página 22 å This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry. å And to celebrate, why not share your success story? No load 25 lbs. 25 lbs. 25 lbs. 50 lbs. Page 22 423661 www.sauder.com/services...

  • Página 23: Meuble De Rangement

    élément et conserver le livret pour future référence. GRANDE EXTRÉMITÉ ..........2 18F CONNECTEUR DE MOULURE......2 Pour contacter Sauder DESSUS ................1 36F FIXATION TWIST-LOCK® ........16 en ce qui concerne cet MOULURE AVANT ............1 PLAQUE DE LIAISON ..........4 élément, faire référence...
  • Página 24 Pour commencer l'assemblage, enfoncer seize FIXATIONS LARGE 14 mm NOIRES (1S) à travers les PLAQUES TWIST-LOCK® SAUDER (36F) dans les gros trous dans les D'ATTACHE et dans les trous des MOULURES. EXTRÉMITÉS (A), les PETITES EXTRÉMITÉS (F), le DESSOUS (K) et la TABLETTE (L).
  • Página 25 REMARQUE : Prière de lire les informations importantes sur la Voir l'étape suivante pour réglages des PORTES. sécurité fi gurant sur les pages arrière du manuel d’instructions. Ceci complète l'assemblage. Nettoyer à l’ a ide d’une encaustique pour meubles ou d’un chiff on humide. Essuyer. www.sauder.com/services 423661 Page 25...

  • Página 26: Gabinete Para Almacenaje

    18F CONECTOR DE MOLDURA ........2 et conserver le livret PANEL SUPERIOR ............1 36F SUJETADOR TWIST-LOCK® ......16 pour future référence. Pour contacter Sauder MOLDURA DELANTERA ........1 PLACA DE CONEXIÓN ...........4 en ce qui concerne cet MOLDURA DERECHA ..........1 SOPORTE DE METAL ..........9 élément, faire référence...
  • Página 27 Para comenzar el ensamblaje, empuje dieciséis SUJETADORES MOLDURAS DE EXTREMO (G). Pase cuatro TORNILLOS NEGROS TWIST-LOCK® SAUDER (36F) dentro de los agujeros grandes DE CABEZA GRANDE de 14 mm (1S) a través de las PLACAS DE de los EXTREMOS (A), de los EXTREMOS PEQUEÑOS (F), del CONEXIÓN y dentro de los agujeros en las MOLDURAS.
  • Página 28 Repita este paso para la PUERTA DERECHA (O). Esto completa el ensamblaje. Limpie con su pulimento para Consulte el próximo paso para ajustar la PUERTA. muebles preferido o un paño húmedo. Seque con un paño. Page 28 423661 www.sauder.com/services...
  • Página 29 TOUJOURS décharger les tablettes et les tiroirs, en commençant par les surface supérieures, avant de déplacer le meuble. NE JAMAIS pousser ou tirer un meuble sur de la moquette. Demander à une autre personne de le soulever correctement pour le déplacer et/ou le repositionner. www.sauder.com/services 423661 Page 29...
  • Página 30 SIEMPRE descargue los estantes y cajones, empezando con las superfi cies superiores, antes de moverlo. NUNCA empuje ni tire de los muebles sobre una alfombra. Obtenga que un amigo le ayude a levantarlo correctamente para moverlo y/o reposicionarlo. Page 30 423661 www.sauder.com/services...

  • Página 31: Garantie Limitée De 5 Ans

    à compter de la date d'achat la première fois et qui sont signalés à Sauder dans les limites de couverture de la contre tout défaut de matériaux ou de fabrication des composantes de mobilier Sauder.
  • Página 32 Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the Set a world record for speed? purchase and assembly process was a positive experience Feeling good about yourself? and you feel good about the furniture you just built. If you Nice.

Este manual también es adecuado para:

423661

Tabla de contenido