Remote Control - Revell Control Backflip 3D Manual Del Usuario

• When disposing of batteries, they must
be discharged or their capacity must be
fully depleted. Cover exposed terminals
with adhesive tape in order to prevent
short-circuiting!
Maintenance and care:
• Please only use a clean, damp cloth
to wipe off the model.
• Protect the model and batteries from
direct sunlight and/or direct heat.
• Never allow the remote control and
charging unit to come into contact
with water, because the electronics
will be damaged as a result.
Technical changes and differences in
color reserved!
1A Rotors
1B Motors
1C Status LED

2 rEmotE control

2A Trim for rotation
2B 180° flip left
2C Control for thrust and rotation,
press vertically: turbo switch
2D 180° flip right
2E Power LED
2F Display
2G Control for forward/backward and
sideways, press briefly: extended
inverted flight, press and hold:
headless mode
3 insErting battEriEs (rEmotE control)
3A To open the battery com- 3B Insert 4 x 1.5 V AAA batter-
partment, press gently on ies and pay attention to
the marked position of the the polarity specifications,
battery compartment cover as indicated in the battery
(2K) and pull downwards. compartment.
16
Required batteries for the model:
Power supply:
Rated output:
1 x DC 3,7 V / 1,7 Wh
Batteries: 3,7 V
echargeable
LiPo battery (included)
Capacity: 450 mAh
Battery requirement for the
remote control:
Power supply:
DC 6 V
Batteries: 4 x 1.5 V "AAA"
(not included)
USB charger:
Power supply: DC 5V via USB port,
500 mA or higher
Rated output: 4,2 V / 500 mAh max.
1 modEl
1D Battery compartment
1E Battery connection
2H Trim for forwards/backwards
2I Trim for sideways
2J ON/OFF switch
2K Battery compartment cover
3C Close the battery
compartment cover.
4 charging thE modEl
Attention: The battery and motor must cool down for 15 to 30 minutes before charging
and after every flight. Otherwise they can be damaged. The charging process must
be constantly monitored. Always ensure that the charging process takes place on a
fireproof surface in a fire-resistant environment.
• Unplug the battery from the battery connection (1E) and switch off the remote control.
Remove the battery from the model (4A). Plug the USB charger into an open USB port
(4B).
• Plug the white battery plug into the socket of the charger. Make sure that the polarity is
correct in the process (4C). The battery plug must be gently inserted into the charging
socket – DO NOT USE FORCE. If the battery is not correctly inserted into the charging
socket, the battery may become damaged and, under certain circumstances, cause
injury.
• The status LED on the USB charger lights up continuously when the charging process
starts.
• The charging process lasts approx. 60 minutes and must be continuously monitored.
The red LED on the charger goes out as soon as the charging process is finished.
• Disconnect the battery from the charger and disconnect the charger from the USB
port once charging is complete.
The model can fly for approx. 5-7 minutes after a charge time of approx.
60 minutes.
Warning notice: The battery does not normally heat up while charging. If it should
become warm or even hot and/or changes to the surface begin to appear, immediately
discontinue the charging process!
5 start prEparation
The model must be switched on first in order to connect it to the remote control. For
this purpose, slide the battery into the battery compartment of the model and connect
the battery plug to the battery connection (1E). Do not use force and ensure the correct
polarity (5A). Then place the model on an even, flat and stable surface.
Before switching on the remote control, the control for thrust and rotation (2C) must
point down (5B). To switch on the remote control, set the ON/OFF switch (2J) to ON
and move the control for thrust and rotation (2C) briefly all the way up and then back
down again. After approx. 3 seconds, the model activates and is ready for use.
Once you have finished flying, switch the model off first and then the remote control.
6 trim adJustmEnt oF thE control
The model must be switched on first in order to connect it to the remote control.
Its adjustment is simple, but it requires some patience and a feel for it. Please observe
the following instructions precisely: Carefully move the thrust control up and raise the
helicopter approximately 0.5 to 1 metre in altitude.
6A If the model automatically moves slowly or quickly to the left or right ...
gradually press the trim for sideways flight (2I) in the opposite direction.
6B If the model moves by itself slowly or quickly around its own axis ...
press the trim adjustment for rotation (2A) incrementally in the opposite direction.
6C If the model automatically moves slowly or quickly forwards or backwards ...
gradually press the forwards/backwards trim (2H) in the opposite direction.
17