Rowenta STEAMFORCE DW924 Serie Manual De Instrucciones página 4

• If you are using a mains extension lead, ensure that it is corrected rated
(16A) with an earth, and is fully extended.
• Do not unplug your appliance by pulling on the cord.
• Never immerse your steam iron in water or any other liquid. Never hold
it under the tap water.
• Never touch the electric cord with the soleplate of the iron.
• Your appliance gives off steam, which may cause burns, especially when
you are ironing close to the edge of your ironing board.
• Never direct the steam towards people or animals.
• For your safety, this appliance conforms to the applicable standards and
regulations (Low Voltage, Electromagnetic Compatibility, Environmental
Directives).
• This product has been designed for domestic use only. Any commercial
use, inappropriate use or failure to comply with the instructions, the
manufacturer accepts no responsibility and the guarantee will not apply.
Important notice for
Under unfavorable mains conditions, phenomena like transient voltage
drops or lighting fluctuations can happen. Therefore, it is recommended
that the iron is connected to a power supply system with a maximum
impedance of 0,15 . If necessary, the user can ask the public power supply
company for the system impedance at the interface point.
ENVIRONMENT PROTECTION FIRST !
Your appliance contains valuable materials which can be recovered or recycled.
Leave it at a local civic waste collection point.
Keep these instructions
2400 W models only :
2
DESCRIPTION
LED screen
1.
with Electronic Temperature Control
Shot of steam button
2.
Steam ON / Steam OFF
3.
4. Cord
5. Handle
6. Spray trigger
Water tank
7.
STEAMFORCE, CONCENTRATED INNOVATION...
Small in size , Steamforce combines power and performance thanks to the compact steam
generator built inside the iron. With unparalleled steam generation capacity reaching
230g/min and variable steam of up to 65g/min, Steamforce pushes up to 50% more steam*
into the fibres of your fabric. This extra steam at the heart of the fabric is the secret of perfect
ironing and long-lasting results.
The movement sensor is an intelligent system which temporarily stops steam being released
when the iron is not moving, even when it is placed horizontally. This function eliminates
wasted steam while you are handling the clothes !
Throughout the ironing session, the LED screen displays the selected fabric type: as soon as
the appropriate temperature is reached, the user is informed directly via the screen. This is
ideal for protecting the most delicate garments.
* compared with an iron with no pump
BEFORE USE
IMPORTANT Before doing anything else, remove the sticker on the side fig.1 -
Depending on model. Warning! Before using your iron with the steam function for
the first time, we recommend that you operate the steam in a horizontal position
for a few moments, away from your linen, i.e. press the Shot of Steam button a
few times.
During the first few uses, a harmless odour and a small amount of smoke may be
noticeable.
This has no effect on the use of the iron and will cease quickly.
Upon the first use, you may notice small particles coming out of the soleplate. This
is parf of manufacturing process and is not harmful to you or your garments. It will
disappear after several uses. You may accelerate this by using the self cleaning
function (fig.13a - 13b) and shaking the iron gently.
WHAT WATER MAY BE USED ?
Your iron has been designed to operate using untreated tap water. If in doubt, check with your
local water authority. However, if your water is very hard, you can mix 50% untreated tap
water with 50% distilled or demineralised water.
IMPORTANT Heat concentrates the elements contained in water during evaporation.
The types of water listed below contain organic waste or mineral elements that can
cause spitting, brown staining or premature wear of the appliance:
water from tumble dryers, scented or softened water, water from refrigerators,
batteries or air conditioners, pure distilled or demineralised water or rain water should
not be used in your iron. Also do not use boiling, or bottled mineral water.
USE
1 • Filling the water tank
• Before filling the water tank, unplug the iron fig.2.
• Set the temperature control dial
fig.3
• Open the filling inlet fig.4. Fill in water up to the Max. mark. fig.5. Close the filling
inlet and return the iron to the horizontal position.
• You can plug in your iron .
fig.6
2 • Setting the temperature
Your iron is equipped with the Autosteam Electronic Control function, it automatically
adjusts the steam amount and the temperature based on the selected fabric for
optimum results. Select the fabric to be ironed by turning the thermostat and
checking the fabric to be ironed on the display fig.7. For perfect results, an optimum
position for each fabric has been pre-defined. You can also set your iron based on
the international temperature measurements • •• •••.
When your iron reaches the required temperature, the selected fabric in the LED
screen stops flashing and is displayed constantly fig.7. You can start ironing.
Self clean button
8.
Spray
9.
High precision tip
10.
Soleplate
11.
Filling inlet
12.
Temperature control dial
13.
14. Rear Cover
on position (Min.)
3
EN