Installation Precautions; Machine Connection; Water Tank; Circuit Priming - Philips Saeco HD 8423 Instrucciones De Uso

4 INSTALLATION
For your own and other people safety, carefully follow
the "Safety Regulations" indicated in chapter 3.
4.1 Packaging
The original packaging has been designed and manufactured
to protect the machine during transport. We recommend
keeping the packaging material for possible future transport.

4.2 Installation Precautions

Before installing the machine, read the following safety pre-
cautions carefully:
• Place the machine in a safe place.
• Make sure children cannot play with the machine.
• Do not place the machine on hot surfaces or near open
fl ames.
The coff ee machine is now ready to be connected to the electric
network.
Note: we recommend washing the components
before using them for the fi rst time and/or af-
ter they have not been used for a certain period of time.

4.3 Machine Connection

Electric power may be very dangerous! It is
therefore necessary to strictly follow the safety
regulations. Do not use faulty power cords. Faulty cords
and plugs must be replaced immediately by Authorised
Service Centres.
The voltage of the appliance has been pre-set by the manu-
facturer. Check that the voltage matches the indication on the
data plate at the bottom of the appliance.
• Insert the plug into a wall socket with suitable power volt-
age.

4.4 Water tank

• (Fig.1A) - Remove the lid from the water tank (2) by lifting
it.
• (Fig.1B) - Remove the water tank (5).
• (Fig.2) - Rinse it and fi ll it with fresh drinking water: do
not exceed the (MAX) level indicated in the water tank.
Fill the tank only with fresh, non-sparkling,
drinking water. Hot water or any other liquid
may damage the tank. Do not operate the machine
• 20 •
All manuals and user guides at all-guides.com
without water: make sure that there is enough water
in the tank.
• (Fig.3A) - Insert the water tank making sure that it has
(THE REFERENCE MARK SHOWN IN FIG.3B SHOULD BE
COMPLETELY VISIBLE). This is to avoid water leaks from
its bottom.

4.5 Circuit Priming

At the beginning, after dispensing steam or when the water
tank is empty, the machine's water circuit must be primed.
• Press the ON/OFF button (11); the light (18) will turn on to
• (Fig.4) - Place a container under the steam wand (Pan-
• Open the "hot water/steam" knob (3) by turning it coun-
• (Fig.5) - Set the selection knob (17) to the "
• Wait until a steady jet of water fl ows out of the steam
• (Fig.5) - Set the selection knob (17) to the " " position.
• Close the "hot water/steam" knob (3) by turning it clock-
4.6 Using the Machine for the First Time
This simple operation ensures an optimum brewing and must
be performed:
- at fi rst start-up;
- when the machine remains inactive for a long time (more
the container fi lls up during the cycle, stop dispensing
water and empty the container before resuming the
operation.
• (Fig.2) - Rinse the tank and fi ll it again with fresh drinking
• (Fig.4) - Place a container under the steam wand (Pan-
• Dispense the whole water tank content from the steam/
been properly repositioned in its former seat and then
reposition the lid (2).
Make sure that the tank is fully inserted in the
machine by pressing it gently up to its limit stop
indicate that the machine is on.
narello).
ter-clockwise.
wand (Pannarello).
wise. Remove the container.
or After a Period of Inactivity
than 2 weeks).
Dispensed water must be emptied into an ad-
equate drain. It is not suitable for food use. If
water.
narello). Open the knob (3) by turning it counter-clockwise.
(Fig.5) - Set the selection knob (17) to the "
hot water wand (Pannarello). To end the operation, set the
selection knob (17) to the " " position and close the knob
" position.
" position.