Noise Information; Safety Instructions For Mitre Saws; English - Milwaukee M18 FMS305 Manual De Instrucciones

Technical Data
Mitresaw
Production code
No-load speed
Battery voltage
Frequency band
Radio-frequency power
Bluetooth version
Saw blade dia. x hole dia
Saw blade body thickness max.
Saw blade tooth thickness min.
Recommended Ambient Operating Temperature
Recommended battery types
Recommended charger
Max. cutting capacity
Mitre 0°/ Bevel 0°
Mitre 45°/ Bevel 0°
Mitre 0°/ Bevel L45°
Mitre 0°/ Bevel R45°
Mitre L45°/ Bevel L45°
Mitre L45°/ Bevel R45°
Mitre R45°/ Bevel L45°
Mitre R45°/ Bevel R45°
Weight according EPTA-Procedure 01/2014 (Li-Ion 2,0 ... 12,0 Ah)

Noise information

Measured values determined according to EN 62841. Typically, the A-weighted noise levels of the tool are
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
WARNING!
The declared noise emission value(s) were measured according to a standardized test method according to EN 62841 and can be used to compare one
power tool with another. The declared noise emission value(s) may also be used in a preliminary assessment of exposure.
The noise emissions during actual use of the power tool can differ from the declared values depending on the ways in which the tool is used especially
what kind of workpiece is processed.
Identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts
of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).
Wear ear protectors. Exposure to noise can cause hearing loss.
WARNING Read all safety warnings, instructions,
illustrations and specifications provided with this power tool.
Failure to follow all instructions listed below may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.

SAFETY INSTRUCTIONS FOR MITRE SAWS

a) Mitre saws are intended to cut wood or wood-like products,
they cannot be used with abrasive cut-off wheels for cutting
ferrous material such as bars, rods, studs, etc. Abrasive dust cau-
ses moving parts such as the lower guard to jam. Sparks from abrasive
cutting will burn the lower guard, the kerf insert and other plastic parts.
b) Use clamps to support the workpiece whenever possible. If
supporting the workpiece by hand, you must always keep your
hand at least 100 mm from either side of the saw blade. Do
not use this saw to cut pieces that are too small to be securely
clamped or held by hand. If your hand is placed too close to the saw
blade, there is an increased risk of injury from blade contact.
c) The workpiece must be stationary and clamped or held
against both the fence and the table. Do not feed the workpi-
ece into the blade or cut "freehand" in any way. Unrestrained or
moving workpieces could be thrown at high speeds, causing injury.
M18 FMS305
4696 77 02...
...000001 - 999999
3600 min
-1
18 V
2402 MHz - 2480 MHz
1,8 dBm
BLE113 BT
305 x 30 mm
2,2 mm
3,0 mm
- 18 °C ... +50 °C
M18B..., M18HB...
M12-18..., M1418 C6
GB GB
340 mm x 96,5 mm
235 mm x 96,5 mm
340 mm x 65 mm
340 mm x 40 mm
235 mm x 65 mm
235 mm x 40 mm
235 mm x 65 mm
235 mm x 40 mm
21,9 ... 23,0 kg
96,2 db(A)
107,5 db(A)

English

27 27