Grohe GROHTHERM 1000 NEW 34 143 Manual Del Usuario página 5

GB
Safety notes
Protection against scalding
It is recommended that near points of discharge with
particular sensitivity to the outlet temperature
(hospitals, schools, nursing and retirement homes)
thermostatic devices should be installed which can limit the
water temperature to 43 °C. The product includes an
appropriate temperature end stop. It is generally
recommended that the temperature of shower-systems should
not exceed 38 °C in nurseries and specific areas of care
centres. Use Grohtherm Special thermostats with special
handle to facilitate thermal disinfection and appropriate safety
end stop. Applicable standards (e. g. EN 806-2) and technical
regulations for drinking water must be observed.
Application
Thermostat mixers are designed for hot water supply via
pressurised storage heaters and, utilised in this way, provide
the best temperature accuracy. With sufficient power output
(from 18 kW or 250 kcal/min), electric or gas instantaneous
heaters are also suitable.
Thermostats cannot be used in conjunction with
non-pressurised storage heaters (displacement water
heaters).
All thermostats are adjusted in the factory at a flow pressure
of 3 bar on both sides.
Should temperature deviations occur on account of special
installation conditions, the thermostat must be adapted to local
conditions (see Adjusting).
Specifications
Minimum flow pressure without
downstream resistances
Minimum flow pressure with
downstream resistances
Max. operating pressure
Recommended flow pressure
Test pressure
Flow rate at 3 bar flow pressure
Bath
Shower
Max. water temperature at hot water supply
Recommended max. flow temperature (energy saving) 60 °C
Thermal disinfection possible
Safety stop
Hot water temperature at supply connection min. 2 °C higher
than mixed water temperature
Cold water connection
Hot water connection
Minimum flow rate
If static pressure exceeds 5 bar, a pressure reducing valve
must be fitted.
Installation
Flush piping system prior and after installation of fitting
thoroughly (Consider EN 806)!
Install unions and screw-mount the mixer, see fold-out page I,
Fig. [1].
Refer to the dimensional drawing on fold-out page I.
The projection can be increased by 20mm with an extension,
see Replacement Parts, fold-out page III, Prod. no. 07 130.
Open cold and hot-water supply and check connections
for water-tightness.
Reversed connection (hot on right - cold on left).
Replace thermostatic compact cartridge, see Replacement
parts, fold-out page III, Prod. no.: 47 175 (1/2").
When using this thermostatic compact cartridge, the Cool
Touch function is no longer available.
Adjusting
Temperature adjustment, see fold-out page I Fig. [2].
Temperature limit stop
If the temperature end stop is at 43 °C, insert accompanying
temperature limiter in temperature selection handle,
see Fig. [3].
Temperature limitation
The safety stop limits the temperature range to 38 °C.
The 38 °C limit can be overridden by pressing the button,
see Fig. [4].
Shower mixer:
Adjusting the economy stop, see fold-out page II Fig. [5].
If a higher flow rate is desired, the stop can be overridden by
pressing the button, fold-out page II Fig. [6].
Bath mixer:
Handle operation, see fold-out page II Fig. [7].
Eco function, by pressing the button the flow rate for the
shower can be increased.
Prevention of frost damage
When the domestic water system is drained, thermostat
mixers must be drained separately, since non-return valves
are installed in the hot and cold water connections. For this
purpose, the mixer must be removed from the wall.
0.5 bar
Maintenance
1 bar
Inspect and clean all parts, replace if necessary and lubricate
10 bar
with special valve grease.
1 - 5 bar
Shut off the hot and cold water supply.
16 bar
Non-return valve, see fold-out page II, Fig. [8].
Remove connection nipple using a 12mm allen key.
approx. 20 l/min
Install in reverse order.
approx. 25 l/min
Thermostatic compact cartridge, see fold-out page II,
70 °C
Fig. [9].
Install in reverse order.
Readjustment is necessary after every maintenance operation
38 °C
on the thermostatic compact cartridge (see Adjusting).
Aquadimmer (bath mixer), see fold-out page II, Fig. [10].
Ceramic headpart (shower mixer), see fold-out page II,
right
Fig. [5] and [11].
left
Install in reverse order.
= 5 l/min
Unscrew and clean mousseur (13 952) see fold-out page III.
Shower, see fold-out page II, Fig. [12].
The function of the SpeedClean nozzles is guaranteed for a
period of five years.
Thanks to the SpeedClean nozzles, which must be regularly
cleaned, limescale deposits on the rose can be removed by
simply rubbing with the fingers.
Replacement parts, see fold-out page III ( * = special
accessories).
Care
For directions on care, refer to the accompanying Care
Instructions.
2