Troubleshooting; Other Information; Specifications - Denon DRR-201SA Instrucciones De Operación

11

TROUBLESHOOTING

Check the following before you draw the conclusion that your Stereo Cassette Deck is malfunctioning:
1. Are all the connections correct?
2. Are all system components being operated correctly in accordance with the operating instructions?
3. Are the speakers and amplifier/receiver functioning correctly?
I f the tape deck still does not function properly, check the symptom against the list below. If the symptom does not
correspond to the check list, please contact your DENON dealer.
Problem Cause
• Power cord is disconnected.
• Tape is loose.
Tape does not run.
• Cassette is not loaded properly.
• Defective cassette.
Tape is not recorded • No cassette is loaded.
when Rec/Rec Mute • Erase prevention tabs are broken off.
button (REC/REC MUTE) (
) is pressed.
4
• Heads, capstan or pinch roller are
dirty.
• Tape is wound too tight.
Sound is warbled or
distorted.
• Recording input level is too high.
• Tape is worn out and has "drop-
outs".
• Tape is worn.
• Heads, capstan or pinch roller are
dirty.
Excessive noise.
• Heads are magnetized.
• Recording input level is too low.
High frequency range • Dolby NR switch (DOLBY NR) is set
(treble) is emphasized. improperly.
High frequency range • Heads are dirty.
• Tape is worn.
(treble) is lost.
• If the Power Operation switch is
turned off either during recording or
playback and the unit is stopped,
The cassette tape cannot
there may be cases when the
be removed.
cassette cannot be removed, even if
the Eject button (EJECT 5 ) is
pressed.
All manuals and user guides at all-guides.com
Refer to
Remedy
page
• Check power cord.
5
• Tighten tape with a pencil, etc.
7
• Load cassette properly.
7
• Replace cassette.
–
• Load cassette. 7
• Cover holes with adhesive tape. 7
• Clean them. 7
• Fast forward or rewind to loosen –
tape winding.
• Adjust recording input level. 8
• Replace tape. –
• Replace them. –
• Clean them. 7
• Demagnetize heads. 13
• Adjust recording input level. 8
• Set Dolby NR switch (DOLBY NR) 6 , 8
properly.
• Clean them. 7
• Replace tape.
7
• Turn the Power Operation switch ¢
ON again, and then press the Stop
button ( 2 STOP).
• Now, press the Eject button (EJECT
5 ) to remove the cassette tape.
12

OTHER INFORMATION

Cleaning the Heads
• If the cassette deck's head are dirty, tapes cannot be
played or recorded with good sound quality.
• To take full advantage of all the performance this
cassette deck has to offer and ensure good quality
sound, clean the heads periodically after approximately
10 hours of use, using a commercially available cleaning
cassette.
Demagnetizing the Heads
• The heads become magnetized after they have been used for an extended period of time or if they are exposed to a
magnetic object. This results in noise or a loss of the treble sound.
• If the heads are magnetized, use a commercially available cassette-type head demagnetizer to demagnetize them.
13

SPECIFICATIONS

Type: 4-track 2-channel auto reverse stereo cassette tape deck (flat loading mechanism)
Heads: Hard permalloy recording/playback head x 1
Double-cap ferrite erasing head x 1
Motors: Electronically-controlled DC motor (for capstan) x 1
DC motor (for reel) x 1
Tape speed: 4.8 cm/sec.
Fast-forward and rewinding time: Approx. 110 seconds for C-60 cassette tapes
Recording bias: Approx. 105 kHz
General S/N ratio (for 3% T.H.D. level), Dolby NR type C on: Metal tape: 74 dB
(CCIR/ARM)
General frequency response: Metal tape: 25 Hz to 19 kHz ±3 dB (–20 dB recording)
Channel separation: 45 dB or greater (1 kHz)
Crosstalk: 65 dB or greater (1 kHz)
Wow & flutter: 0.08 or less (W.RMS)
Line input: 90 mV at maximum input level
Input impedance: 30 kΩ
Line output: 500 mV (with 47 kΩ load, 200 nwb/m playback)
Power supply: AC 230V, 50 Hz
Power consumption: 13W (Approx. 1W in standby mode)
External dimensions: 250 (width) x 90 (height) x 356 (depth) mm (including feet, controls and jacks)
Weight: 3.6 kg
For improvement purposes, specifications and design are subject to change without notice.
Dolby noise reduction and HX Pro headroom extension manufactured under license from Dolby Laboratories
2
Licensing Corporation. HX pro originated by Bang & Olufsen,
"DOLBY", the double-D symbol
2 and "HX PRO" are trademarks of Dolby Laboratories Licensing Corporation.
ENGLISH
NOTE:
• Some commercially available cleaning cassettes are
highly abrasive and may damage the heads. Avoid
using such cleaning cassettes.
13