Steam Features; Using The Steam Refresh Cycle - Sears Kenmore 796.8138 Manual De Uso Y Cuidado

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

1
STEAM FEATURES
WARNING:
• Do not open the dryer door during Steam Cycles.
Steam can cause severe burns.
• Do not fill the steam feeder with gasoline, dry cleaning
solvents, or other flammable
or explosive
substances.
They give off vapors that could explode.
• Do not drink water from the steam feeder.
• Do not fill the steam feeder with hot water (over
86°F/30°C).
• Do not touch the steam nozzle in the drum during or
after the steam cycle.
IMPORTANT
NOTES ABOUT STEAM FUNCTIONS:
• Steam may not be clearly visible during the steam
functions.
This is normal.
• Do not use Steam Refresh with items such as wool,
wool blankets, leather jackets, silk, wet clothes, lingerie,
foam products, or electric
blankets.
• For best results, load articles of similar size and fabric
type. Do not overload.
• If the home's exhaust system is restricted,
the
performance
of the steam functions will be reduced.
• During steam operation,
the clothes will tumble for
only a few seconds, once a minute.
• The steam feeder must be filled with water up to the
MAX line. Otherwise,
the ADD WATER light
may illuminate.
Using the STEAM REFRESH cycle
The Steam Refresh cycle uses the power of steam to
quickly
reduce wrinkles and odor in fabrics.
It brings
new life to wrinkled
clothes that have been stored for
an extended
period of time, and it can make heavily
wrinkled
clothes easier to iron. STEAM REFRESH can
also be used to help reduce odors in clothes, such as
clothes that were worn in a room where people had
been smoking. This cycle can refresh from one to five
garments, or one bulky item such as a comforter.
There
are three settings available.
Use
for one to three
garments
and _ for four or five garments. The b I_
(big) setting should be used for bulky items. Best results
are achieved
with 70/30
cotton/polyblend
fabrics.
NOTE: The STATIC SHIELD option can be used together
with the STEAM REFRESH cycle to help prevent
static electricity
after the cycle.
_I
Turn the dryer ON and select the STEAM REFRESH
cycle.
O
Select the STATIC SHIELD option, if desired.
The default number of garments is three. Press the
MORE TIME or LESS TIME button to adjust the load
size, as described
above.
0
Press the START/PAUSE button to start the cycle.
STATIC SHIELD
i
I
This °pti°n
uses steam late in the
@ Static %ield
drying
cycle to reduce the static
_ ro_ _'d_
electricity
caused by dry fabrics
rubbing
together.
Change the steam time by pressing
the MORE TIME and LESS TIME buttons to display the
approximate
number of articles in the load: 7, 9, 11, 14,
16 or 18.
NOTE: When STATIC SHIELD is added to auto dry
cycles, the Damp Dry level cannot be selected.
IRON READY
i
I
The Ir°n Ready °pti°n
pr°vides
@ Static %ield
uniform, properly
dampened
fabrics
_ ro_ _'d_/
for ironing, which can save time and
make ironing easier. Change the steam time by pressing
the MORE TIME or LESS TIME button, depending
on the
number of garments
in the load: 1, 2, 3, 4, or 5.
Press and hold the STATIC SHIELD button for three
seconds to access the Iron Ready function.
NOTE: After the STATIC SHIELD or IRON READY op-
tion is selected in timed dry cycles, the MORE TIME and
LESS TIME buttons will change the number of garments,
as described
above. After the cycle has started, the
MORE TIME and LESS TIME buttons are disabled.
26

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Kenmore 796.9138

Tabla de contenido