Special Safety Instructions; Noise And Vibration; Before Initial Operation - Flex DD 2G 10.8-LD Instrucciones De Funcionamiento Originales

DD 2G 10.8-LD
 Liquid may leak out of the battery if the battery is
incorrectly used. Avoid contact with such liquid. If
contact accidentally occurs, rinse with water. If liquid
contacts eyes, seek medical attention. Liquid discharged
from the battery may cause irritation or burns.
 Recharge batteries only with chargers recommended
by the manufacturer. A charger that is suitable for one type
of battery may create a fire hazard when used with another
battery.
 The battery may be damaged by pointed objects such
as e.g. nails or screwdrivers or by external application
of force. This may give rise to an internal short circuit,
causing the battery to burn, smoke, explode or overheat.
Charger
 Always check whether the mains voltage matches
the voltage indicated on the type plate of the
charger.
 The charger plug must fit in the power socket. Never
modify the plug in any way. Do not use any adapter
plugs together with earthed (grounded) power tools.
Unmodified plugs and matching power sockets will reduce
the risk of electric shock.
 Only use the charger in dry rooms and avoid all
contact with moisture and rain.
The ingress of water into the charger increases the risk of
electric shock.
 Never use the charger if cables, plugs or the device
itself are damaged as a result of external influence.
Take the charger to the nearest authorised repair shop.
 Under no circumstances open the charger. In the
event of a fault, take it to an authorised repair shop.
 Do not place any objects on the charger and do not
place the charger on soft surfaces. Fire hazard!

Special safety instructions

 Before carrying out any work on the power tool, move
the direction preselector switch (2) to the middle
position.
 Operate the direction preselector switch (2) or torque
setting turning dial (4) only when the tool is stopped.
 Identify the power tool with stickers only.
Do not drill any holes into the housing.

Noise and vibration

NOTE
Values for the A-weighted sound pressure level and for the
total vibration values can be found in the table on page 6.
The noise and vibration values have been determined in
accordance with EN 60745.
WARNING!
The indicated measurements refer to new power tools. Daily
use causes the noise and vibration values to change.
NOTE
The vibration emission level given in this information sheet has
been measured in accordance with a measurement method
standardised in EN 60745 and may be used to compare one
tool with another. It may be used for a preliminary assessment
of exposure. The specified vibration emission level represents
the main applications of the tool.
However, if the tool is used for different applications, with
different cutting accessories or poorly maintained, the
vibration emission level may differ.
This may significantly increase the exposure level over the
total working period.
To make an accurate estimation of the vibration exposure level,
it is also necessary to take into account the times when the tool
is switched off or running but not actually in use. This may
significantly decrease the exposure level over the total working
period.
Identify additional safety measures to protect the operator from
the effects of vibration such as: maintain the tool and the cutting
accessories, keep the hands warm, organisation of work
patterns.
CAUTION!
Wear ear defenders at a sound pressure above 85 dB(A).
Overview (Figure A)
1 Trigger switch
For switching on and off and for accelerating up to
maximum rotational speed
2 Direction preselector switch
3 Speed selector switch
4 Turning dial for torque setting
5 Keyless chuck
6 Workplace lighting
7 Handle
8 Insertion slot for battery
9 Li-ion battery (2.5 Ah/4.0 Ah/6.0 Ah)
10 Release button for battery
11 State of charge indicator
12 Belt clip
13 Bit holder
14 Fastening screw
Instructions for use

Before initial operation

 Unpack the power tool and accessories and check that
no parts are missing or damaged.
 Attach the belt clip and bit holder with the enclosed
fastening screw (Figure B).
NOTE
The batteries are not fully charged on delivery. Prior to initial
operation, charge the batteries fully. See "Charger (Figure
L)/Charging process".
13