Ego Power+ STA1500 Manual Del Operador página 10

USING THE LINE TRIMMER WITH POWER HEAD
EN
WARNING:
Dress properly to reduce the risk of
injury when operating this tool. Do not wear loose clothing
or jewelry. Wear eye and ear/hearing protection. Wear
heavy, long pants, boots and gloves. Do not wear short
pants or sandals or go barefoot.
WARNING:
Clear the area to be cut before each use.
Remove all objects, such as rocks, broken glass, nails, wire,
or string that can be thrown or become entangled in the
cutting attachment. Clear the area of children, bystanders,
and pets. At a minimum, keep all children, bystanders
and pets at least 15m away; there still may be risk to
bystanders from thrown objects. Bystanders should be
encouraged to wear eye protection. If you are approached,
stop the motor and cutting attachment immediately.
For safe and better operation, put on the shoulder strap
across the shoulder. Adjust the shoulder strap in a
comfortable operating position. Hold the line trimmer with
your one hand on the rear handle and your other hand
on the front-assist handle. Keep a firm grip with both
hands while in operation. The line trimmer should be held
at a comfortable position with the rear handle about hip
height. The trimmer head should be parallel to the ground
such that it easily contacts the material to be cut without
the operator having to bend over (Fig. B).
WARNING:
The shoulder strap is also a quick
release mechanism in hazardous situation. When
emergency occurs, take it off from your shoulder
immediately, no matter what way the strap is in.
After each use, clean the trimmer
See the MAINTENANCE section for cleaning instructions.
TO START/STOP THE TOOL
See "STARTING/STOPPING THE POWER HEAD" section
in the power head PH1400E operator's manual.
ADJUSTING CUTTING LINE LENGTH
The trimmer head allows the operator to release more
cutting line without stopping the motor. As line becomes
frayed or worn, additional line can be released by lightly
tapping the trimmer head on the ground while operating
the trimmer (Fig. E).
NOTICE:
Line release will become more difficult as the
cutting line becomes shorter.
WARNING:
Do not remove or alter the line-cutting
blade assembly. Excessive line length will cause the motor
to overheat and may result in serious personal injury.
10
LINE TRIMMER ATTACHMENT — STA1500
LINE REPLACEMENT
NOTICE:
Always use the recommended nylon cutting line
with a diameter that does not exceed 2.4 mm. Using line
other than that specified may cause the line trimmer to
overheat or become damaged.
WARNING:
Never use metal-reinforced line, wire,
or rope, etc. These can break off and become dangerous
projectiles.
1. Remove the battery pack
2. Remove the remaining cutting line, if necessary.
Simply pull it out by hand.
3. Cut 4m long cutting line, Insert the line into the
mounting hole inside the eyelet (Fig. F). Push and pull
the line from the other side until equal amounts of
line appear on both sides of the spool.
4. Press, while rotating the lower cover assembly in the
arrow direction, to wind the line onto the spool until
approximately 14cm of line is showing on each side
(Fig. G).
5. Push the lower cover assembly down while pulling on
the lines to manually advance the line and to check
for proper assembly of the trimmer head.
When the cutting line breaks from the line outlet or the
cutting line is not released when tapping the trimmer
head, follow the steps below:
1. Remove the battery pack.
2. Press the release tabs on the upper cover and remove
the lower cover assembly by pulling it straight out (Fig.
H& I).
3. Remove the cutting line from the spool.
4. With one hand holding the Upper cover, use the other
hand to grasp the lower cover assembly and align the
tabs on the upper cover with the holes lower cover
assembly base (Fig. J); use your palm to press and
rotate the lower cover assembly left and right until
the tabs lock with the upper cover (Fig. K).
5. Following the instructions in "LINE REPLACEMENT" to
reload the cutting line.
When the tool is intended to use as a brush cutter, follow
the steps as Fig. L & M shown to disassemble the trimmer
head.
MAINTENANCE
WARNING:
Before inspecting, cleaning or servicing
the unit, stop the motor, wait for all moving parts to stop,
and remove the battery pack. Failure to follow these
instructions can result in serious personal injury or
property damage.