KIKKA BOO TILT Instrucciones De Uso página 5

YOU CAN USE YOUR CHILD SAFETY SEAT AS FOLLOWS:
• In the direction of travel ---- YES
• Against the direction of travel -- NO
• with 2-point belt • with 3-point belt -- NO
• with ISOFIT fastening points(between seat surface andbackrest ) -- YES
• on front passenger seat -- YES
• on outer rear seat --- YES
• on centre rear seat (with3-point belt) --- YES
Conventional use in cars equipped with ISOFIT connector.
1.1 - IMAGE - ATTENTION! FOR YOUR CHILD'S DRIVING SAFETY,THE FOLLOWING CONDITIONS SHOULD BE PROHIBITED
• Please read user manual carefully, and install correctly the child seat according to user manual.
• Child not allowed to stand and play on the child seat without the belt.
• Please install the child car seat correctly according to the using manual.
• To insure the lifetime of the child seat pls avoid the direct sunlight.
• In any circumstance ,the child seat can not be used in the front passenger seat with an active airbag .
2 - IMAGE - GROUP II , III : 15-36 KG
ATTENTION
Try best to avoid of the seat belt loosen and child seat rocking or others. Adjust the shoulder belt in suitable position and do not struck the child's neck. When
use child safety seat every time. Ms re-check the installation is okay or not. The CARSEAT is approved for two methods of installation:
GRUP II(15-25KG) -- INSTALLATION - VEHICLE BELT - CHILD INSTALLATION - VEHICLE BELT
GROUP II(15-25KG)-- INSTALLATION - ISOFIT+VEHICLE BELT -- CHILD INSTALLATION -- VEHICLE BELT
VEHICLE 3 - POINT BELT
1.) Pull out the vehicle belt and uide it in front of your child to the vehicle seat buckle.
2.) Tighten the vehicle seat belt by pulling on the diagonal seat belt section
3 - IMAGE Group II, III INSTALLATION - VEHICLE 3 POINT BELT WITH ISOFIT
OPEN ISOFIT INTERFACE - Press the button in the side of ISOFIT parts,then ISOFIT interface goes out.
INSTALLATION -Insert the FIX into the FIX connector. TheFIX indicator will become green if install correctly, then push the child car seat in the direction of car
seat back, make sure there is no space between the child car seat and car back.
4 - IMAGE - 1.) Inser into the ISOFIT connetor ; 2.)Correct installation ; 3.) Incorrect installation;
5 - IMAGE - CHILD INSTALLATION
1.) Pull out the vehicle belt and guide it in front of your child to the vehicle seat buckle.
2.) Tighten th0e vehicle seat belt by pulling on the diagonal seat belt section
6 - IMAGE - SEAT REMOVE
Press the button in the side of ISOFIT interface, then the ISOFIT interface opens, move baby car seat away.
7 - IMAGE - ADJUST THE HEADREST HEIGHT
Headrest can move up and down,and adjust it to suitable position. ATTENTION PLEASE CONFIRM THE HEADREST IS LOCKED
8 - IMAGE - MULTIPLY-ADJUSTABLE SITTING POSITION
To pull the seat at the bottom of the red handle, can adjust the seat Angle. The seat has four Angle xed position. Loosen the shake handshandle, ne-tuning to
lock chair body position. (Gear indicator)
9 - IMAGE - ASIP Installation
Seat with stationary (chair around each have one) and removable type two kinds of lateral protection mode. Stationary side protection for original parts no installation.
1.)Press the switch on the removable ASIP control activity mechanism of it.
2.)According to the instruction from the ASIP surface corresponding to the xed end inserted into the bayonet xed ASIP. The removable type ASIP attention:
right under stationary After the installation is ASIP armor. Release the complete please shake ASIP switch. ASIP installation is successful.
ATTENTION - THE INSTALLATION IS COMPLETE , PLEASE SHAKE ASIP TO CHECK WHETHER THE CORRECT INSTALLATION
3.) Remove the ASIP - Press the switch on the removable ASIP control activity mechanism of it. Then seperate the ASIP from the seat.
10- IMAGE - CARE AND MAINTENANCE
Put the shoulder belt through the suitable shoulder belt slot, and then connect to the should belt yoke.
ATTENTION THERE ARE FEW HOOKS ON THE PLASTIC PARTS TO CONNECT THE SEAT FABRIC, PLEASE SEPERATE THE CONNECTION POINTS FIRST, THEN TAKE OFF THE FABRIC.
DO NOT PULL HARD DIRECTLY TO DAMAGE THE POINTS OF CONNECTION .
1.) Headrest Hook ; 2.) Seat Hook ; 3.)Back of the chair Hook ; 4.) Base Hook
11 - IMAGE - 11 Washing
Important: The cover is a safety feature, never use the child seat without it. Don' t put your child' s safety at risk by using other makes of replacement cover,could
stop the child seat form protecting your child as well as it Washing instruction: The cover is removable and washable at 30C line dry only.
1.) Machine wash, cold ; 2.) Do not bleach ; 3.) Do not dry ; 4. Do not tumble dry ; 5. Do not iron
ENGLISH